Poulan HD21H42 manual To Replace Mower Blade Drive Belt See Fig, Belt Removal, Belt Installation

Page 20

SERVICE AND ADJUSTMENTS

SIDE-TO-SIDE ADJUSTMENT (See Figs. 15 and 16)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Three full turns of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE OF

 

BOTTOM EDGE

MOWER

 

OF MOWER

TO GROUND

 

TO GROUND

“A”

GROUND LINE

“A”

FIG. 15

SUSPENSION ARM

LIFT LINK ADJUSTMENT NUT

FIG. 16

FRONT-TO-BACK ADJUSTMENT (See Figs. 17 and 18)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its high- est position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns. The two front links must remain equal in length.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

MANDREL

"D"

"D"

FIG. 17

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT "F"

NUT "E"

TRUNNION

FRONT LINKS

FIG. 18

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 19)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Remove mower from tractor (See “TO REMOVE MOWER” in this section of this manual).

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Install new belt in reverse order of removal.

•Make sure belt is in all pulley grooves and inside all belt guides.

•Install mower in reverse order of removal instruc- tions.

MANDREL

IDLER

PULLEY

PULLEYS

MANDREL

 

PULLEY

 

FIG. 19

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents HD21H42 Always Wear EYE Protection During OperationSafety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Slope Sheet Unassembled PartsSteering Wheel Seat Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Using the Reverse Operation System To Operate Mower See FigReverse Operation System ROS To Operate on HillsBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Purge TransmissionMaintenance Lubrication ChartGeneral Recommendations Before Each USETo Sharpen Blade See Fig TractorBlade Removal See Fig Engine Cleaning Service and Adjustments To Install Mower See FigTo Level Mower Housing To Remove Mower See FigBelt Removal Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Check and Adjust Brake Transaxle Motion Control Lever Neutral Adjustment See FigSee Fig To Replace Motion Drive Belt See FigTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

HD21H42 specifications

The Poulan HD21H42 lawn tractor is a powerful and versatile lawn care machine, designed to meet the needs of homeowners with medium to large-sized lawns. This tractor is equipped with a robust 21 horsepower Briggs & Stratton engine, providing the ideal balance between power and efficiency. Its reliable engine ensures smooth operation while delivering ample torque for tackling various terrains and grass conditions.

One of the standout features of the HD21H42 is its 42-inch cutting deck, which allows for efficient mowing of larger areas. The deck is designed with a durable steel construction, ensuring longevity and resistance to wear and tear. The cutting height is adjustable, offering a range of settings that cater to different grass types and seasonal growth patterns. This adaptability is crucial for achieving a perfectly manicured lawn.

The Poulan HD21H42 also incorporates an advanced hydrostatic transmission system. This technology allows for an effortless driving experience, offering infinite speed control without the need for shifting gears. Users can easily maneuver around obstacles and navigate tight spaces with confidence, significantly enhancing the tractor's usability.

Comfort is another key characteristic of the Poulan HD21H42. The tractor features an ergonomic seat that provides support during long mowing sessions, along with a high backrest for added comfort. The straightforward control panel simplifies operation, enabling users to focus on their mowing tasks without confusion. Additionally, the tractor's tight turning radius helps in making sharp turns, reducing the need for manual adjustments.

Maintenance is straightforward with the HD21H42, as its removable cutting deck makes it easy to access and clean. Regular maintenance routines contribute to prolonging the lifespan of the machine and ensuring consistent performance over time.

Moreover, the Poulan HD21H42 offers enhanced versatility with optional attachments such as mulching kits, baggers, and snow plows. This allows homeowners to extend the utility of their lawn tractor throughout different seasons, adapting it to varied tasks beyond just mowing.

In conclusion, the Poulan HD21H42 lawn tractor combines power, ease of use, and adaptability, making it an excellent choice for homeowners seeking a reliable lawn maintenance solution. Its advanced features and thoughtful design ensure that mowing the lawn is not only an obligation but a satisfying and efficient task.
Top Page Image Contents