Poulan HD21H42 Tools Required for Assembly, To Remove Tractor from Carton, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1)

3/4" wrench

Pliers

(1)

1/2" wrench

Tire pressure gauge

 

 

Utility knife

INSERT

5/16 HEX BOLT

5/16 LOCK WASHER

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

STEERING WHEEL

LARGE FLAT WASHER

STEERING

BOOT

•Remove all accessible loose parts and parts cartons from carton.

•Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft.

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, 5/16 lock washer, 5/16 hex bolt and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

TABS

ADAPTER

EXTENSION

SHAFT

LOWER

STEERING

SHAFT

TAB

SLOTS

FIG. 1

INSTALL SEAT (See Fig. 2)

Adjust seat before tightening adjustment knob.

•Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjustment knob and flat washer loosely. Do not tighten.

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment knob securely.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents HD21H42 Always Wear EYE Protection During OperationGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts Steering Wheel SeatSlope Sheet To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS Using the Reverse Operation SystemTo Operate Mower See Fig To Operate on HillsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Purge TransmissionGeneral Recommendations MaintenanceLubrication Chart Before Each USETractor Blade Removal See FigTo Sharpen Blade See Fig Engine Cleaning To Level Mower Housing Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigBelt Installation To Replace Mower Blade Drive Belt See FigBelt Removal See Fig To Check and Adjust BrakeTransaxle Motion Control Lever Neutral Adjustment See Fig To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

HD21H42 specifications

The Poulan HD21H42 lawn tractor is a powerful and versatile lawn care machine, designed to meet the needs of homeowners with medium to large-sized lawns. This tractor is equipped with a robust 21 horsepower Briggs & Stratton engine, providing the ideal balance between power and efficiency. Its reliable engine ensures smooth operation while delivering ample torque for tackling various terrains and grass conditions.

One of the standout features of the HD21H42 is its 42-inch cutting deck, which allows for efficient mowing of larger areas. The deck is designed with a durable steel construction, ensuring longevity and resistance to wear and tear. The cutting height is adjustable, offering a range of settings that cater to different grass types and seasonal growth patterns. This adaptability is crucial for achieving a perfectly manicured lawn.

The Poulan HD21H42 also incorporates an advanced hydrostatic transmission system. This technology allows for an effortless driving experience, offering infinite speed control without the need for shifting gears. Users can easily maneuver around obstacles and navigate tight spaces with confidence, significantly enhancing the tractor's usability.

Comfort is another key characteristic of the Poulan HD21H42. The tractor features an ergonomic seat that provides support during long mowing sessions, along with a high backrest for added comfort. The straightforward control panel simplifies operation, enabling users to focus on their mowing tasks without confusion. Additionally, the tractor's tight turning radius helps in making sharp turns, reducing the need for manual adjustments.

Maintenance is straightforward with the HD21H42, as its removable cutting deck makes it easy to access and clean. Regular maintenance routines contribute to prolonging the lifespan of the machine and ensuring consistent performance over time.

Moreover, the Poulan HD21H42 offers enhanced versatility with optional attachments such as mulching kits, baggers, and snow plows. This allows homeowners to extend the utility of their lawn tractor throughout different seasons, adapting it to varied tasks beyond just mowing.

In conclusion, the Poulan HD21H42 lawn tractor combines power, ease of use, and adaptability, making it an excellent choice for homeowners seeking a reliable lawn maintenance solution. Its advanced features and thoughtful design ensure that mowing the lawn is not only an obligation but a satisfying and efficient task.
Top Page Image Contents