Poulan DPR22H46STB Before Starting the Engine, To Operate on Hills, Check Engine OIL Level

Page 14

OPERATION

Remove retainer spring and clevis pin which secure each gauge wheel bar.

Lower gauge wheels to ground. Raise gauge wheels slightly to align holes in bracket and gauge wheel bar and insert clevis pin. Gauge wheels should be slightly off the ground.

Replace retainer spring into clevis pin.

IMPORTANT: BE SURE TO READJUST GAUGE WHEELS IF YOU CHANGE THE CUTTING HEIGHT OF THE MOWER DECK.

RETAINER

SPRING

CLEVIS

PIN

FIG. 11

TO OPERATE MOWER (See Fig. 12)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.

Select desired height of cut.

Lower mower with attachment lift control.

Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflec- tor shield in place.

ATTACHMENT CLUTCH

ATTACHMENT

SWITCH PULL OUT TO

LIFT LEVER

"ENGAGE"

HIGH

 

POSITION

 

LOW

 

POSITION

PUSH IN TO

 

"DISENGAGE"

 

FIG. 12

TO OPERATE ON HILLS

CAUTION: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

Choose the slowest speed before starting up or down hills.

Avoid stopping or changing speed on hills.

If slowing is necessary, move throttle control lever to slower position.

If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake.

Move motion control lever to neutral (N) position.

IMPORTANT: THE MOTION CONTROL LEVER DOES NOT RETURN TO NEUTRAL (N) POSITION WHEN THE CLUTCH/BRAKE PEDAL IS DEPRESSED.

To restart movement, slowly release parking brake and clutch/brake pedal.

Slowly move motion control lever to slowest setting.

Make all turns slowly.

TO TRANSPORT (See Figs. 9 and 13)

When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor.

Raise attachment lift to highest position with attachment lift control.

Pull freewheel control out and down into the slot and release so it is held in the disengaged position.

Do not push or tow tractor at more than two (2) MPH.

To reengage transmission, reverse above procedure.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

FIG. 13

TOWING CARTS AND OTHER ATTACH- MENTS

Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

The engine in your tractor has been shipped, from the factory, already filled with summer weight oil.

Check engine oil with tractor on level ground.

Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

For cold weather operation you should change oil for easier starting (See “OIL VISCOSITY CHART” in the Customer Responsibilities section of this manual).

To change engine oil, see the Customer Responsibili-

14ties section in this manual.

Image 14
Contents DPR22H46STB General Operation IV. ServiceSafe Operation Practices for Ride-On Mowers II. Slope OperationSafety Rules Table of Contents Unassembled Parts HOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig To Attach Nose Roller See FigAssemble Gauge Wheels to Mower Deck See Fig To SET UP Your Mower for Mulching See FigTo Install Mulcher Plate See Fig To Convert to Bagging or DischargingInstall Mower and Drive Belt See Figs Check for Proper Position of ALL Belts Check Tire PressureCheck Mower Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Towing Carts and Other ATTACH- Ments Before Starting the EngineTo Operate on Hills Check Engine OIL LevelPurge Transmission ADD GasolineTo Start Engine See Fig Mowing Tips Mulching Mowing TipsGeneral Recommendations Lubrication ChartCustomer Responsibilities Before Each USETractor Engine Spark Plugs CleaningMuffler Engine OIL FilterTo Level Mower Housing Service and AdjustmentsTo Install Mower To Remove Mower See FigTo Replace Mower Drive Belt To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig To Adjust Brake See FigTransaxle Motion Control Lever Neutral Adjustment See Fig To Start Engine with a Weak Battery See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb Replacing Battery See FigTo Remove Hood and Grill Assembly See Fig Interlocks and RelaysTo Adjust Carburetor To Adjust Throttle Control Cable See FigTo Adjust Choke Control See Fig Fuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionOFF Service Notes Schematic Tractor Model Number DPR22H46STBElectrical 178861 17720408178450 Chassis and Enclosures 175582 174619174997 175692X428Drive 72140608 175417178289 175456Steering Assembly 155105 175121177883 175146164067 Control Throttle EngineSpark Arrester 148315Seat Assembly 178249 DecalsWheels & Tires 178250Mower Lift Mower Deck 74780616 17608419131312 175746Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Sighting GuideParts and Service