Poulan PC1538A manual Tractor, Brake Operation, Tires, Operator Presence System, Blade Care

Page 15

CUSTOMER RESPONSIBILITIES

TRACTOR

Always observe safety rules when performing any mainte- nance.

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are work- ing properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the clutch/brake pedal is fully depressed and attachement clutch control is in the disengaged position.

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

BLADE REMOVAL (See Fig. 8)

•Raise mower to highest position to allow access to blades.

•Remove blade bolt, lock washer and flat washer secur- ing blade.

•Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Reassemble blade bolt, lock washer and flat washer in exact order as shown.

•Tighten blade bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: BLADE BOLT IS GRADE 8 HEAT TREATED.

MANDREL

TRAILINGASSEMBLY EDGE UP

CENTER

HOLE

LOCK WASHER

STAR

BLADE

FLAT WASHER

BLADE BOLT (GRADE 8)*

*A GRADE 8 HEAT TREATED BOLT CAN BE IDENTIFIED BY SIX LINES ON THE BOLT HEAD.

FIG. 8

TO SHARPEN BLADE (See Fig. 9)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An unbalanced blade will cause excessive vibration and even- tual damage to mower and engine.

•The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer).

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

CENTER HOLE

5/8" BOLT

BLADE

OR PIN

 

FIG. 9

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Model NO. PC1538A II. Slope Operation Safety RulesIV. Service General OperationSafe Operation Practices for Ride-On Mowers Safety RulesTable of Contents Steering Wheel Unassembled PartsBefore Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonHOW to SET UP Your Tractor Check Battery See FigInstall Seat See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Check Engine OIL Level Before Starting the EngineTo Transport Towing Carts and Other ATTACH- MentsMowing Tips ADD GasolineTo Start Engine See Fig General Recommendations Lubrication ChartService Dates Customer ResponsibilitiesOperator Presence System TractorBrake Operation TiresEngine Spark Plugs CleaningMuffler AIR Filter See FigService and Adjustments To Install Mower See FigTo Remove Mower See Fig Belt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigTo Adjust Brake See Fig To Adjust Steering Wheel AlignmentFront Wheel TOE-IN/CAMBER To Remove CABLES, Reverse Order To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Attach Jumper CablesTo Replace Fuse To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysEngine OIL StorageOther Fuel SystemTroubleshooting Points OFF Service Notes Tractor - Model Number PC1538A, Product Number 954 56 SchematicElectrical KEY Part Description Chassis Repair Parts Drive Transaxle See Breakdown Steering 140044X428 Wheel Steering 175131 Axle Asm Optional Equipment 170551 Control Th/ch Flag Seat LBD48 DecalsWheels & Tires LSB42Mower Lift 159460 Wire Asm Inner/Sprg w/plunger Mower Deck Repair Parts Service Notes Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

PC1538A specifications

The Poulan PC1538A is a versatile and reliable gas-powered chainsaw designed for homeowners and outdoor enthusiasts looking to tackle a variety of cutting tasks. With a focus on user-friendliness and efficient performance, this model stands out for its robust features and innovative technologies.

One of the primary characteristics of the PC1538A is its powerful 38cc two-stroke engine. This engine provides a balance of power and economy, enabling users to handle everything from light pruning to larger cutting jobs with ease. The engine is designed for optimal fuel efficiency while maintaining a solid power output, ensuring that users can work longer without frequent refueling.

The 15-inch bar and chain setup of the PC1538A is ideal for making quick cuts in relatively small to medium-sized wood, making it a perfect choice for backyard projects, cutting firewood, and managing fallen branches. The chainsaw's low-kickback chain further enhances safety for the user, allowing for more controlled cuts without the risk of unintended recoil.

Ergonomic design is another hallmark of the Poulan PC1538A, featuring a lightweight frame that is easy to maneuver. The comfortable grip handle reduces vibration, making prolonged use more tolerable and less strenuous on the hands and arms. This thoughtful design consideration allows users to maintain better control over the tool, leading to more precise cutting.

In terms of maintenance, Poulan has integrated several user-friendly features into the PC1538A. The tool-less chain tensioning system allows for quick adjustments to the chain tension, ensuring optimal performance without the need for additional tools. An easy-access air filter simplifies routine maintenance, enabling users to keep the engine running smoothly with minimal effort.

Additionally, the chainsaw incorporates technologies such as a primer bulb to facilitate easier starts, especially after long periods of inactivity. The automatic oiler system ensures proper lubrication of the chain and bar during operation, extending the life of the accessory components and maintaining cutting efficiency.

Overall, the Poulan PC1538A combines its powerful engine, ergonomic design, and thoughtful features to provide a reliable tool for a range of cutting tasks. Whether you are a novice or an experienced user, this chainsaw offers performance and efficiency, making it an excellent addition to any outdoor toolkit.
Top Page Image Contents