Poulan PC1538A manual To Start Engine with a Weak Battery See Fig, Replacing Battery See Figs

Page 21

SERVICE AND ADJUSTMENTS

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 23

TO START ENGINE WITH A WEAK BATTERY (See Fig. 24)

CAUTION: Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from bat- teries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Customer Responsibili- ties section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT NEGATIVE GROUNDED SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT NEGATIVE GROUNDED SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect each end of the RED cable to the POSITIVE (+) terminal of each battery, taking care not to short against chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal of fully charged battery.

•Connect the other end of the BLACK cable to good CHASSIS GROUND, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

POSITIVE TERMINAL

 

NEGATIVE TERMINAL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CHASSIS

 

 

CABLES

POSITIVE

NEGATIVE

TERMINAL

TERMINAL

CHARGED

 

 

BATTERY

REPLACING BATTERY (See Figs. 25 and 26)

CAUTION: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from acciden- tal grounding.

•Lift seat pan to raised position.

•Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal.

•Connect BLACK grounding cable to negative (-) terminal with remaining hex bolt and keps nut. Tighten securely.

SEAT PAN

 

FIG. 25

 

 

TERMINAL COVER

KEPS

 

NUT

HEX

BOLT

POSITIVE

NEGATIVE

(RED) CABLE

(BLACK) CABLE

 

FIG. 26

FIG. 24

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Model NO. PC1538A IV. Service Safety RulesGeneral Operation II. Slope OperationSafe Operation Practices for Ride-On Mowers Safety RulesTable of Contents Steering Wheel Unassembled PartsTools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidHOW to SET UP Your Tractor Check Battery See FigInstall Seat See Fig Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Transport Before Starting the EngineTowing Carts and Other ATTACH- Ments Check Engine OIL LevelMowing Tips ADD GasolineTo Start Engine See Fig Service Dates Lubrication ChartCustomer Responsibilities General RecommendationsBrake Operation TractorTires Operator Presence SystemEngine Muffler CleaningAIR Filter See Fig Spark PlugsService and Adjustments To Install Mower See FigTo Remove Mower See Fig Belt Installation To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Adjust Brake See Fig To Adjust Steering Wheel AlignmentFront Wheel TOE-IN/CAMBER Replacing Battery See Figs To Start Engine with a Weak Battery See FigTo Attach Jumper Cables To Remove CABLES, Reverse OrderTo Replace Headlight Bulb To Adjust CarburetorInterlocks and Relays To Replace FuseOther StorageFuel System Engine OILTroubleshooting Points OFF Service Notes Tractor - Model Number PC1538A, Product Number 954 56 SchematicElectrical KEY Part Description Chassis Repair Parts Drive Transaxle See Breakdown Steering 140044X428 Wheel Steering 175131 Axle Asm Optional Equipment 170551 Control Th/ch Flag Seat Wheels & Tires DecalsLSB42 LBD48Mower Lift 159460 Wire Asm Inner/Sprg w/plunger Mower Deck Repair Parts Service Notes Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

PC1538A specifications

The Poulan PC1538A is a versatile and reliable gas-powered chainsaw designed for homeowners and outdoor enthusiasts looking to tackle a variety of cutting tasks. With a focus on user-friendliness and efficient performance, this model stands out for its robust features and innovative technologies.

One of the primary characteristics of the PC1538A is its powerful 38cc two-stroke engine. This engine provides a balance of power and economy, enabling users to handle everything from light pruning to larger cutting jobs with ease. The engine is designed for optimal fuel efficiency while maintaining a solid power output, ensuring that users can work longer without frequent refueling.

The 15-inch bar and chain setup of the PC1538A is ideal for making quick cuts in relatively small to medium-sized wood, making it a perfect choice for backyard projects, cutting firewood, and managing fallen branches. The chainsaw's low-kickback chain further enhances safety for the user, allowing for more controlled cuts without the risk of unintended recoil.

Ergonomic design is another hallmark of the Poulan PC1538A, featuring a lightweight frame that is easy to maneuver. The comfortable grip handle reduces vibration, making prolonged use more tolerable and less strenuous on the hands and arms. This thoughtful design consideration allows users to maintain better control over the tool, leading to more precise cutting.

In terms of maintenance, Poulan has integrated several user-friendly features into the PC1538A. The tool-less chain tensioning system allows for quick adjustments to the chain tension, ensuring optimal performance without the need for additional tools. An easy-access air filter simplifies routine maintenance, enabling users to keep the engine running smoothly with minimal effort.

Additionally, the chainsaw incorporates technologies such as a primer bulb to facilitate easier starts, especially after long periods of inactivity. The automatic oiler system ensures proper lubrication of the chain and bar during operation, extending the life of the accessory components and maintaining cutting efficiency.

Overall, the Poulan PC1538A combines its powerful engine, ergonomic design, and thoughtful features to provide a reliable tool for a range of cutting tasks. Whether you are a novice or an experienced user, this chainsaw offers performance and efficiency, making it an excellent addition to any outdoor toolkit.
Top Page Image Contents