Poulan PR17H42STC, 178219 owner manual Tractor

Page 16

CUSTOMER RESPONSIBILITIES

TRACTOR

Always observe safety rules when performing any mainte- nance.

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are work- ing properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the clutch/brake pedal is fully depressed and attachement clutch control is in the disengaged position.

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

BLADE REMOVAL (See Fig. 12)

•Raise mower to highest position to allow access to blades.

•Remove hex bolt, lock washer and flat washer securing blade.

•Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Reassemble hex bolt, lock washer and flat washer in exact order as shown.

•Tighten bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: BLADE BOLT IS GRADE 8 HEAT TREATED.

TRAILING

MANDREL

ASSEMBLY

EDGE UP

 

BLADE

 

 

CENTER

 

HOLE

LOCK WASHER

STAR

FLAT WASHER

HEX BOLT (GRADE 8)*

*A GRADE 8 HEAT TREATED BOLT CAN BE

IDENTIFIED BY SIX LINES ON THE BOLT HEAD.

FIG. 12

TO SHARPEN BLADE (See Fig. 13)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An unbalanced blade will cause excessive vibration and even- tual damage to mower and engine.

•The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer).

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

CENTER HOLE

5/8" BOLT

BLADE

OR PIN

 

FIG. 13

BATTERY

Your tractor has a battery charging system which is suffi- cient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents PR17H42STC Safety Rules Safe Operation Practices for Ride-On MowersBecome ALERT!!! Your Safety is IN- Volved Table of Contents Steering Wheel Seat Unassembled PartsSlope Sheet Assembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig To SET UP Your Mower for Mulching Check Tire PressureCheck Deck Levelness To Convert to Bagging or DischargingOperation Know Your Tractor HOW to USE Your Tractor To Adjust Mower Cutting Height See Fig Stopping See FigTo SET Parking Brake See Fig To USE Throttle Control See FigTo Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To Transport See FigsBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Mulching Mowing TipsLubrication Chart Customer ResponsibilitiesGeneral Recommendations Before Each USETractor Engine Muffler CleaningSpark Plugs Service and Adjustments To Install Mower See FigTo Level Mower Housing To Remove Mower See FigTo Replace Mower Blade Drive Belt See Fig Belt InstallationBelt Removal To Adjust Brake See Fig Transmission REMOVAL/REPLACEMENTTransaxle Motion Control Lever Neutral ADJUSTMENTSee Fig To Replace Motion Drive Belt See FigTo Adjust Steering Wheel Alignment To Start Engine with a Weak Battery See FigReplacing Battery See Figs Front Wheel TOE-IN/CAMBERInterlocks and Relays To Replace Headlight BulbTo Replace Fuse Storage OtherFuel System Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number PR17H42STCElectrical 2122KEY Part Description Chassis 174619 Drive 175765 175578175461 175556Steering Assembly 175121 177876175146 175118Seat Assembly Decals Wheels and Tires178206 178219Engine Optional EquipmentSpark Arrester 8113170551 Control Th/ch Flag Mower Deck 143 159 144 150 145 148 146 142 147147 142 14917490612 175746175747 157109X421Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Service Notes Service Notes Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Sighting GuideParts and Service

178219, PR17H42STC specifications

The Poulan 178219, PR17H42STC is a powerful and versatile riding lawn mower designed to meet the needs of homeowners seeking a reliable solution for maintaining their lawns. With a robust build and innovative features, this mower stands out in the competitive market of outdoor power equipment.

One of the main features of the Poulan PR17H42STC is its 17 HP Briggs & Stratton engine, which provides ample power for cutting through thick grass and tackling uneven terrain. The engine is designed for easy starting and reliable performance, ensuring that users can depend on their mower season after season.

The 42-inch cutting deck is another highlight of this riding mower. This size allows for efficient mowing of larger grass areas while still being compact enough to maneuver around garden beds and other landscaping features. The deck is equipped with a dual-blade system, which ensures a clean and even cut, promoting a healthy lawn.

In terms of technology, the Poulan PR17H42STC features a hydrostatic transmission that offers smooth and responsive speed adjustments. This technology allows for effortless acceleration and deceleration, making it easy for users to navigate around obstacles. The mower also includes a tight turning radius, enhancing its maneuverability in tighter spaces.

Comfort and convenience are key considerations in the design of the Poulan PR17H42STC. The adjustable high back seat provides excellent support, allowing users to mow for extended periods without discomfort. The mower also features easy-access controls, including mower engagement and speed controls, which are intuitively placed for user-friendly operation.

Another notable characteristic is the durable construction of the mower. Built with high-quality materials, the Poulan PR17H42STC is designed to withstand the rigors of regular use. Additionally, the mower is equipped with reinforced cutting deck edges, extending its lifespan and ensuring it maintains its performance over time.

With its blend of power, technology, and user-friendly features, the Poulan 178219, PR17H42STC is an excellent choice for homeowners looking to efficiently care for their lawns. Its combination of performance, comfort, and durability makes it a reliable partner for all mowing tasks.
Top Page Image Contents