Poulan 178219, PR17H42STC To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

Page 23

SERVICE AND ADJUSTMENTS

•Install new battery with terminals in same position as old battery.

•First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely.

•Connect BLACK grounding cable to negative (-) terminal with remaining hex bolt and keps nut. Tighten securely.

•Close battery box door.

SEAT PAN

BATTERY

BOX DOOR

FIG. 30

KEPS

NUT

HEX

BOLT

POSITIVE (RED)

NEGATIVE

CABLE

(BLACK) CABLE

FIG. 31

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 32)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT WIRE CONNECTOR

FIG. 32

ENGINE

TO ADJUST THROTTLE CONTROL CABLE (See Fig. 33)

The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

•With engine not running, move throttle control lever from slow to choke position. Slowly move lever from choke to fast position.

•Check that holes “A” in governor control lever and hole in governor plate line-up. If holes “A” are not aligned, loosen clamp screw and move throttle cable until holes are aligned. Tighten clamp screw securely.

GOVERNOR

GOVERNOR

CONTROL LEVER

CONTROL PLATE

 

CLAMP

THROTTLE

SCREW

HOLES “A”

CABLE

FIG. 33

TO ADJUST CARBURETOR (See Fig. 33)

The carburetor has been preset at the factory and adjust- ment should not be necessary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, see engine manual.

High speed stop is factory adjusted. Do not adjust - damage may result.

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE THE FACTORY HIGH SPEED SETTING CAN BE DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR N E A R E S T A U T H O R I Z E D S E R V I C E C E N T E R / DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND E X P E R I E N C E T O M A K E A N Y N E C E S S A R Y

23ADJUSTMENTS.

Page 22 Page 24
Image 23
Page 22 Page 24
Contents PR17H42STC Safe Operation Practices for Ride-On Mowers Safety RulesBecome ALERT!!! Your Safety is IN- Volved Table of Contents Slope Sheet Unassembled PartsSteering Wheel Seat To Remove Tractor from Carton AssemblyTools Required for Assembly HOW to SET UP Your TractorInstall Seat See Fig To Convert to Bagging or Discharging To SET UP Your Mower for MulchingCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor To USE Throttle Control See Fig HOW to USE Your TractorTo Adjust Mower Cutting Height See Fig Stopping See Fig To SET Parking Brake See FigTo Transport See Figs To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsTo Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolineMulching Mowing Tips Mowing TipsBefore Each USE Lubrication ChartCustomer Responsibilities General RecommendationsTractor Engine Spark Plugs CleaningMuffler To Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower HousingBelt Removal Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See Fig To Adjust Brake See FigTransmission REMOVAL/REPLACEMENT Transaxle Motion Control Lever Neutral ADJUSTMENTSee FigFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel AlignmentTo Start Engine with a Weak Battery See Fig Replacing Battery See FigsTo Replace Fuse To Replace Headlight BulbInterlocks and Relays Engine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number PR17H42STC Schematic2122 ElectricalKEY Part Description Chassis 174619 Drive 175556 175765175578 175461Steering Assembly 175118 175121177876 175146Seat Assembly 178219 DecalsWheels and Tires 1782068113 EngineOptional Equipment Spark Arrester170551 Control Th/ch Flag 149 Mower Deck143 159 144 150 145 148 146 142 147 147 142157109X421 17490612175746 175747Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Service Notes Service Notes Limited Warranty Sighting Guide Suggested Guide for Sighting Slopes for Safe OperationParts and Service

178219, PR17H42STC specifications

The Poulan 178219, PR17H42STC is a powerful and versatile riding lawn mower designed to meet the needs of homeowners seeking a reliable solution for maintaining their lawns. With a robust build and innovative features, this mower stands out in the competitive market of outdoor power equipment.

One of the main features of the Poulan PR17H42STC is its 17 HP Briggs & Stratton engine, which provides ample power for cutting through thick grass and tackling uneven terrain. The engine is designed for easy starting and reliable performance, ensuring that users can depend on their mower season after season.

The 42-inch cutting deck is another highlight of this riding mower. This size allows for efficient mowing of larger grass areas while still being compact enough to maneuver around garden beds and other landscaping features. The deck is equipped with a dual-blade system, which ensures a clean and even cut, promoting a healthy lawn.

In terms of technology, the Poulan PR17H42STC features a hydrostatic transmission that offers smooth and responsive speed adjustments. This technology allows for effortless acceleration and deceleration, making it easy for users to navigate around obstacles. The mower also includes a tight turning radius, enhancing its maneuverability in tighter spaces.

Comfort and convenience are key considerations in the design of the Poulan PR17H42STC. The adjustable high back seat provides excellent support, allowing users to mow for extended periods without discomfort. The mower also features easy-access controls, including mower engagement and speed controls, which are intuitively placed for user-friendly operation.

Another notable characteristic is the durable construction of the mower. Built with high-quality materials, the Poulan PR17H42STC is designed to withstand the rigors of regular use. Additionally, the mower is equipped with reinforced cutting deck edges, extending its lifespan and ensuring it maintains its performance over time.

With its blend of power, technology, and user-friendly features, the Poulan 178219, PR17H42STC is an excellent choice for homeowners looking to efficiently care for their lawns. Its combination of performance, comfort, and durability makes it a reliable partner for all mowing tasks.
Top Page Image Contents