Poulan PPH25K54 manual Service and Adjustments, To Remove Mower See Fig, To Install Mower

Page 21

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:

•Depress brake pedal fully and set parking brake.

•Place attachment clutch in “DISENGAGED” position.

•Turn ignition key to “STOP” and remove key.

•Make sure the blades and all moving parts have completely stopped.

•Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TO REMOVE MOWER (See Fig. 32)

•Place attachment clutch in “DISENGAGED” position.

•Lower attachment lift lever to its lowest position.

•Disengage belt tension rod (K) from lock bracket (L).

CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and release slowly.

•Remove mower belt from electric clutch pulley (M).

•Disconnect front link (E) from mower - remove retainer spring and washer.

•Go to either side of mower and disconnect mower suspension arm (A) from chassis and rear lift link (C) from rear mower bracket (D) - remove retainer springs and washers.

•Go to other side of mower and disconnect the suspen- sion arm and rear lift link.

CAUTION: After rear lift links are discon- nected, the attachment lift lever will be spring loaded. Have a tight grip on lift lever when changing position of the lever.

•From right side of mower, disconnect anti-sway bar (S) from right rear mower bracket (D) - remove retainer spring and washer and pull mower toward you until the bar falls from the hole in bracket.

•Turn tractor steering wheel to the left as far as it will go.

•Slide mower out from under right side of tractor.

TO INSTALL MOWER

Follow procedure described in “INSTALL MOWER AND DRIVE BELT” in the Assembly section of this manual.

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 33)

MOWER DRIVE BELT REMOVAL

•Park tractor on a level surface. Engage parking brake.

•Lower attachment lift lever to its lowest position.

•Disengage belt tension rod (K) from lock bracket (L).

CAUTION: Belt tension rod is spring loaded. Have a firm grip on rod and release slowly.

•Remove screws (P) from mandrel covers (Q) and remove covers.

•Removeanydirtorgrassclippingswhichmayhaveaccu- mulated around mandrels and entire upper deck surface.

•Remove belt from electric clutch pulley (M), both man- drel pulleys (R) and all idler pulleys (V).

MOWER DRIVE BELT INSTALLATION

•Install belt around all mandrel pulleys (R) and around idler pulleys (V) as shown.

•Install belt onto electric clutch pulley (M).

IMPORTANT: Check belt for proper routing in all mower pulley grooves.

•Reassemble mandrel covers (Q). Securely tighten all screws.

•Engage belt tension rod (K) on locking bracket (L).

CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and engage slowly.

•Raise attachment lift lever to highest position.

 

L

 

 

B

M

 

 

 

 

 

 

F

 

 

 

 

 

 

 

 

 

 

 

 

E

K

 

 

 

A

 

 

 

 

 

 

 

H

 

 

 

 

 

 

C

D

S

 

 

 

 

 

C

D

 

 

 

 

 

 

 

 

 

 

 

Fig. 32

 

21

 

 

 

 

 

 

P

P

 

 

 

L

M

P

 

Q

 

K

R

Q

R

V

 

 

R

 

Fig. 33

Page 20 Page 22
Image 21
Page 20 Page 22
Contents PPH25K54 Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Unassembled Parts MowerSlope Sheet Tools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidTo Adjust Seat See Fig To Install Mower See FigsAssemble Front Wheel to Mower See Fig First Install ANTI-SWAY BAR S Check Tire Pressure Mower Drive Belt InstallationCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Aqjk Know Your TractorTo SET Parking Brake See Fig HOW to USE Your TractorStopping See Fig To USE Throttle Control D See FigTo Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigTo Move Forward and Backward See Fig To USE Cruise Control J See FigReverse Operation System ROS Service REMINDER/HOUR MeterTowing Carts and Other Attachments To Operate MowerCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigPurge Transmission Mowing TipsLubrication Chart MaintenanceTractor BatteryBlade Care Blade Removal See FigEngine Clean AIR Screen CleaningAIR Filter MufflerTo Install Mower Service and AdjustmentsTo Remove Mower See Fig To Replace Mower Blade Drive Belt See FigPrecision SIDE-TO-SIDE Adjustment See Fig Visual SIDE-TO-SIDE Adjustment See FigTo Level Mower Turn nut right Turn nut left To raise mowerTo Check Brake To Adjust Steering Wheel AlignmentTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBERReplacing Battery See Fig To Start Engine with a Weak Battery See FigTo Attach Jumper Cables To Remove CABLES, Reverse OrderTransmission Other StorageFuel System Engine OILProblem Cause Correction TroubleshootingBattery will not To run when operFires when turn Engine continuesSuggested Guide for Sighting Slopes for Safe Operation Parts and Service Changere DE Pièces LES ET L’ENTRETIEN Degrés MAX Correction Cause Problème Dépannage DE GuideManque moteur Le Puissance dePas démarre Ne moteur le maisEntreposage Reglages ET Revision MoteurSionmistrans Rossage -AVANT/CAR Roues DES Convergence Fig la Voir Batterie LA ReplacerTionrecdi LA DE L’ALIGNEMENT Régler Pour 41 .FigFig la Voir D’ENTRAÎNEMENT Fig la Voir TionsrapaCourroie Acer Rempl Pour RÉ LES Pour Roues LES Enlever Pour37 .Fig Tondeuse LA Niveau LE Ajuster Pour36 .Fig 35 .Fig33 .Fig Tondeuse LA Installer Pour32 .Fig Réglages OU SionsFig La Voir Coupe DE Plateau DU Lavage DE Raccord Entretien’ALLUMAGE Bougie ’AIR Tamis LE NettoyerSionmistrans LA DE Moteur Fluide 29 et 28 .Fig la VoirLames DES Entretien Fig la Voir Lame LA EnleverPneus Frein DU FonctionnementLubrification DE Tableau Utilisation Chaque AvantUtilisation Gaz plein à gaz des commande la avec toujours TondezTransmission LA Purger 25 .FigMoteur DU D’HUILE Niveau LE Vérifier ’ESSENCE Réservoir LE RemplirQueti Maauto Transmission LA DE RéchauffementROS Arrière Marche EN Fonctionnement DE Système Accessoires Autres ET Charrettes DES Remorquer PourTracteur LE Transporter Pour Pentes LES Dans Utiliser PourFig la Voir J Vitesse DE Régulateur LE Utiliser Comment Jauge DE Roues LES Régler PourTondeuse DE Lames LES Arrêter Pour Tondeuse LA Utiliser Pour18 .Fig GAZ DES Commande LA Utiliser PourFig la Voir Mentnetionsta DE Frein LE Embrayée Pour Moteur15 .Fig ’EMBRAYAGE Montage 10 .Fig 12 .Fig 11 .FigLA DE Avant Roue LA Assemblez Courroie LA ET Tondeuse LA InstallerEt 3 .Figs les Voir Siège LE Ajustez Tionrecdi DE Volant LE FixerCarton LE Deballer Pente-Guide Assemblé PAS PiècesEntreposage Montage UtilisationClient DU Responsabilités Produit DE SpécificationsTracteurs des sécurité toute Sécurité DE RèglesEnfants En l’utilisation pour ConseilsPentes LES Dans Fonctionnement AvertissementTracteurs des sécurité toute en l’utilisation pour Conseils Général FonctionnementAvertissement U the in Printed SR/AP 09.20.02

PPH25K54 specifications

The Poulan PPH25K54 is a standout model in the lawn care industry, designed specifically for homeowners who seek a reliable and powerful performing lawn mower. This machine is equipped with a potent 25 horsepower engine that delivers ample power for tackling thick grass and uneven terrain. Its robust design ensures durability, making it suitable for various lawn sizes and conditions.

A key feature of the Poulan PPH25K54 is its cutting width of 54 inches, allowing users to cover more ground in fewer passes. This is particularly beneficial for larger yards, reducing mowing time while maintaining a professional-looking lawn. The mower's cutting height is adjustable, offering a range of settings from 1.5 inches to 4 inches. This feature enables users to customize their mowing experience according to grass type and treatment preferences.

The PPH25K54 incorporates advanced technologies that enhance its performance and efficiency. The machine is equipped with a hydrostatic transmission system, allowing for smooth and seamless speed adjustments without the need for shifting gears. This feature not only improves ease of operation but also provides better control, especially on slopes and hilly terrain.

Safety is also a priority in the design of the Poulan PPH25K54. The mower is outfitted with a seat safety switch that prevents operation unless the operator is securely seated, significantly reducing the risk of accidents. Additionally, the durable steel frame adds stability during operation, ensuring users can maneuver the mower confidently.

Maintenance is simplified with the PPH25K54, featuring an easy-to-access oil filter and a spring-assisted deck lift for easier adjustments. This convenience allows homeowners to perform routine maintenance without extensive mechanical knowledge, promoting longevity and optimal performance.

In summary, the Poulan PPH25K54 combines power, efficiency, and user-friendly features that deliver an exceptional mowing experience. Its impressive engine, adjustable cutting height, and hydrostatic transmission make it an ideal choice for those looking to maintain their lawns with ease and precision. With its focus on safety and maintenance ease, this model is designed to meet the demands of any homeowner seeking a reliable and efficient lawn care solution.
Top Page Image Contents