Poulan PR17542STC owner manual Tractor

Page 15

CUSTOMER RESPONSIBILITIES

TRACTOR

Always observe safety rules when performing any mainte- nance.

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TRAILING

EDGE UP

FLAT WASHER

LOCK WASHER

MANDREL

BLADEASSEMBLY

CENTER

HOLE

STAR

TIRES

Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual).

Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are work- ing properly. If your tractor does not function as described, repair the problem immediately.

The engine should not start unless the clutch/brake pedal is fully depressed and attachement clutch control is in the disengaged position.

When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

The attachment clutch should never operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

BLADE REMOVAL (See Fig. 10)

Raise mower to highest position to allow access to blades.

Remove blade bolt, lock washer and flat washer secur- ing blade.

Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

Reassemble blade bolt, lock washer and flat washer in exact order as shown.

Tighten blade bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: BLADE BOLT IS GRADE 8 HEAT TREATED.

BLADE BOLT (GRADE 8)*

*A GRADE 8 HEAT TREATED BOLT CAN BE IDENTIFIED BY SIX LINES ON THE BOLT HEAD.

FIG. 10

TO SHARPEN BLADE (See Fig. 11)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An unbalanced blade will cause excessive vibration and even- tual damage to mower and engine.

The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with bal- ancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

 

CENTER HOLE

5/8" BOLT

BLADE

OR PIN

 

FIG. 11

BATTERY

Your tractor has a battery charging system which is suffi- cient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

Keep battery and terminals clean.

Keep battery bolts tight.

Keep small vent holes open.

Recharge at 6-10 amperes for 1 hour.

NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not

15necessary.

Image 15
Contents PR17542STC II. Slope Operation Safety RulesIV. Service General OperationSafe Operation Practices for Ride-On Mowers Safety RulesTable of Contents Keys Slope Sheet Unassembled HardwareSteering Wheel SeatTo Remove Tractor from Carton AssemblyTools Required for Assembly HOW to SET UP Your TractorInstall Seat See Fig Check Deck Levelness To SET UP Your Mower for MulchingTo Convert to Bagging or Discharging Check Tire PressureOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine Mowing Tips To Start Engine See FigMulching Mowing Tips Before Each USE General Recommendations Lubrication ChartService Dates Customer ResponsibilitiesTractor Engine Spark Plugs CleaningEngine OIL Filter MufflerService and Adjustments To Install Mower see FIGTo Remove Mower see FIG FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Motion Drive Belt See Fig To Adjust Brake See FigBelt Installation To Replace Mower Blade Drive Belt See FigFront Wheel TOE-IN/CAMBER Transaxle Gear Shift Lever Neutral Adjustment See FigTo Adjust Steering Wheel Alignment To Start Engine with a Weak Battery See FigInterlocks and Relays Replacing Battery See FigsTo Remove Hood and Grill Assembly See Fig To Replace Headlight BulbTo Adjust Throttle Control Cable See Fig To Adjust Choke Control See FigTo Adjust Carburetor Engine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsWhen operator leaves Tractor - Model Number PR17542STC, Product Number 954 56 SchematicElectrical KEY Part NO. NO. Description Chassis and Enclosures KEY Part Description Drive Repair Parts Steering Assembly Adaptor Wheel Strg Seat Assembly Wheels and Tires DecalsEngine 170771 Control Th/ch Flag Mower Deck Repair Parts Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Page Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Fold Along This Dotted Line DegreeParts and Service

PR17542STC specifications

The Poulan PR17542STC is a robust and efficient riding lawn mower designed to provide superior lawn care for homeowners with medium to large-sized yards. Known for its durability and performance, this model combines modern technology with user-friendly features, making it an excellent choice for both novice and experienced gardeners.

One of the standout characteristics of the PR17542STC is its powerful 17.5 HP Briggs & Stratton engine. This reliable engine ensures ample power to tackle various lawn types and terrains, providing a smooth and consistent mowing experience. Its automatic transmission allows for easy maneuverability, enabling the user to change speeds without the hassle of shifting gears manually. This feature is particularly beneficial when navigating around obstacles and tight corners.

The mower features a 42-inch cutting deck, which is optimal for achieving a clean and even cut across your lawn. The cutting deck comes equipped with three separate blades, allowing for efficient grass distribution and reducing the need for extensive clean-up afterward. Additionally, the cutting height can be easily adjusted to meet the specific needs of your lawn, offering a customizable mowing experience.

Comfort is prioritized in the design of the PR17542STC, as illustrated by its cushioned seat and ergonomic steering wheel. This ensures that users can enjoy longer mowing sessions without discomfort. The mower also includes a convenient dashboard that displays essential information, such as fuel levels and speed, keeping the user informed at all times.

Technologically advanced features such as a mulching kit are available, allowing homeowners to recycle grass clippings into nutrient-rich mulch. This not only promotes a healthier lawn but also helps reduce waste. Furthermore, the mower’s easy-to-access maintenance points make routine upkeep simple and straightforward, ensuring it remains in excellent condition for many seasons.

Overall, the Poulan PR17542STC stands out as a reliable and efficient riding lawn mower, thanks to its powerful engine, user-friendly features, and advanced technology. Whether you're maintaining a pristine lawn or managing challenging terrain, this mower offers the performance and comfort necessary to achieve your gardening goals, making it a valuable addition to any homeowner's lawn maintenance arsenal.