Poulan PPR2042STA To Adjust Gauge Wheels See Fig, To Operate Mower See Fig, To Operate on Hills

Page 12

OPERATION

TO ADJUST GAUGE WHEELS (See Fig. 7)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole with shoulder bolt, 3/8 washer, and 3/8-16 locknut and tighten securely.

•Repeat for opposite side installing gauge wheel in same adjustment hole.

GAUGE WHEEL

MOUNTING

BRACKET

3/8-16

LOCKNUT

3/8 WASHER

SHOULDER

GAUGE WHEEL

BOLT

 

FIG. 7

TO OPERATE MOWER (See Fig. 8)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.

•Select desired height of cut.

•Lower mower with attachment lift control.

•Start mower blades by engaging attachment clutch control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield in place.

"ENGAGED" POSITION

ATTACHMENT

LIFT LEVER

HIGH POSITION

LOW

POSITION

ATTACHMENT CLUTCH LEVER "DISENGAGED" POSITION

DEFLECTOR

SHIELD

FIG. 8

TO OPERATE ON HILLS

CAUTION: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If slowing is necessary, move throttle control lever to slower position.

•If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake.

•Move gearshift lever to 1st gear. Be sure you have allowed room for tractor to roll slightly as you restart movement.

•To restart movement, slowly release parking brake and clutch/brake pedal.

•Make all turns slowly.

TO TRANSPORT

•Raise attachment lift to highest position with attach- ment lift control.

•When pushing or towing your tractor, be sure gearshift lever is in neutral (N) position.

•Do not push or tow tractor at more than five (5) MPH.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

TOWING CARTS AND OTHER ATTACH- MENTS

Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents PPR2042STA Safety Rules IV. ServiceGeneral Operation II. Slope OperationTable of Contents Product Specifications Customer ResponsibilitiesUnassembled Hardware Steering WheelSeat Slope Sheet KeysAssembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig To SET UP Your Mower for Mulching To Convert to Bagging or DischargingCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To TransportBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Mulching Mowing TipsGeneral Recommendations Lubrication Chart Customer ResponsibilitiesBefore Each USE Tractor Engine Cleaning AIR Filter See FigMuffler Spark PlugsService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Adjust Brake See Fig Transaxle Gear Shift Lever Neutral Adjustment See FigTo Adjust Steering Wheel Alignment To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery Replacing Battery See FigsTo Remove Wheel for Repairs See Fig To Attach Jumper CablesTo Adjust Carburetor To Replace Headlight BulbInterlocks and Relays To Replace FuseStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionWhen operator leaves Schematic Tractor - Model Number PPR2042STAElectrical KEY Part Description Chassis Screw Hex Wshd 8-18 x 7/8 Drive 175410 Pulley Eng Steering Assembly KEY Part NO. NO. Description Seat Assembly Decals Wheels and TiresEngine Optional EquipmentSpark Arrester 170771 Control Throt Mower Deck Washer, Spacer Mower Vented Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Service Notes C U M SEH Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

PPR2042STA specifications

The Poulan PPR2042STA is a notable addition to Poulan’s lineup of outdoor lawn care equipment, specifically designed for those who require efficient and reliable grass cutting. This model stands out due to its powerful performance, user-friendly design, and advanced features that cater to both amateur gardeners and professional landscapers alike.

One of the main features of the PPR2042STA is its robust 42-inch cutting deck. This wide deck allows for efficient mowing of larger lawns without the need for excessive back-and-forth passes, thus reducing mowing time significantly. The deck is equipped with three high-performance blades, ensuring a clean and precise cut every time. With a cutting height adjustment feature, users can easily switch between different grass lengths, adapting to varying lawn conditions.

The PPR2042STA is powered by a 17.5 HP Briggs & Stratton engine, known for its reliability and performance. This engine delivers ample power to tackle thick grass and uneven terrains, making it suitable for diverse landscaping tasks. The automatic drive allows for a smooth operation, enabling users to navigate their lawns without the hassle of manual gear shifting.

Another standout technology integrated into the Poulan PPR2042STA is its innovative air induction mowing system. This system lifts the grass as it is cut, ensuring an even and consistent lawn appearance. Moreover, the mower’s design ensures effective grass discharge, whether utilizing the side discharge feature or connecting a mulching kit for finer grass clippings.

In terms of user comfort, the PPR2042STA boasts an ergonomic steering wheel and adjustable seat that ensures a comfortable ride, even during extended mowing sessions. The compact design of the mower, combined with its responsive controls, enhances maneuverability, making it easy to operate around flower beds, trees, and other obstacles.

Finally, the Poulan PPR2042STA features a durable steel frame that promises longevity, backed by a manufacturer's warranty that provides peace of mind to users. Maintenance is straightforward, with easy access to the engine and mower deck for cleaning and servicing.

With its powerful engine, efficient cutting system, and user-friendly design, the Poulan PPR2042STA represents excellent value for anyone looking to maintain their lawn effectively.
Top Page Image Contents