Poulan PPR2042STA owner manual To Adjust Brake See Fig, To Replace Motion Drive Belt See Fig

Page 21

SERVICE AND ADJUSTMENTS

MANDREL

IDLER PULLEYS

PULLEY

 

MANDREL

 

PULLEY

 

FIG. 21

TO ADJUST BRAKE (See Fig. 22)

Your tractor is equipped with an adjustable brake system which is mounted on the right side of the transaxle.

If tractor requires more than six (6) feet stopping distance at high speed in highest gear on a level dry concrete or paved surface, then brake must be adjusted.

•Depress clutch/brake pedal and engage parking brake.

•Measure distance between brake operating arm and nut “A” on brake rod.

•If distance is other than 1-1/2", loosen jam nut and turn nut “A” until distance becomes 1-1/2". Retighten jam nut against nut “A”.

•Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than six (6) feet in highest gear, further maintenance is necessary. Contact your nearest au- thorized service center/department.

WITH PARKING BRAKE "ENGAGED"

1-1/2"

NUT "A"

JAM NUT

OPERATING

ARM

FIG. 22

TO REPLACE MOTION DRIVE BELT (See Fig. 23)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

•Remove mower (See “TO REMOVE MOWER” in this section of this manual.)

•Remove belt from stationary idler and clutching idler.

•Pull belt slack toward rear of tractor. Remove belt upwards from transaxle pulley by deflecting belt keep- ers.

•Pull belt toward front of tractor and remove downwards from around engine pulley.

•Install new belt by reversing above procedure.

ENGINE

PULLEY

CLUTCHING

IDLER

STATIONARY

IDLER

TRANSAXLE

PULLEY

FIG. 23

TRANSAXLE GEAR SHIFT LEVER NEUTRAL ADJUSTMENT (See Fig. 34)

The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows:

•Make sure transaxle is in neutral (N).

NOTE: When the tractor rear wheels move freely, the transaxle is in neutral.

•Loosen adjustment bolt in front of the right rear wheel.

•Position the gear shift lever in the neutral (N) position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

GEARSHIFT LEVER

NEUTRAL

LOCK GATE

 

ADJUSTMENT

 

BOLT

FIG. 24

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe- in or camber, contact your nearest authorized service center/department.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents PPR2042STA IV. Service Safety RulesGeneral Operation II. Slope OperationTable of Contents Customer Responsibilities Product SpecificationsSteering Wheel Unassembled HardwareSeat Slope Sheet KeysTools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig To Convert to Bagging or Discharging To SET UP Your Mower for MulchingCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To TransportCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigMulching Mowing Tips Mowing TipsGeneral Recommendations Lubrication Chart Customer ResponsibilitiesBefore Each USE Tractor Engine AIR Filter See Fig CleaningMuffler Spark PlugsService and Adjustments To Install Mower See FigTo Remove Mower See Fig Belt Installation To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig Belt RemovalTransaxle Gear Shift Lever Neutral Adjustment See Fig To Adjust Brake See FigTo Adjust Steering Wheel Alignment To Replace Motion Drive Belt See FigReplacing Battery See Figs To Start Engine with a Weak BatteryTo Remove Wheel for Repairs See Fig To Attach Jumper CablesTo Replace Headlight Bulb To Adjust CarburetorInterlocks and Relays To Replace FuseOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsWhen operator leaves Tractor - Model Number PPR2042STA SchematicElectrical KEY Part Description Chassis Screw Hex Wshd 8-18 x 7/8 Drive 175410 Pulley Eng Steering Assembly KEY Part NO. NO. Description Seat Assembly Wheels and Tires DecalsEngine Optional EquipmentSpark Arrester 170771 Control Throt Mower Deck Washer, Spacer Mower Vented Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Service Notes C U M SEH Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

PPR2042STA specifications

The Poulan PPR2042STA is a notable addition to Poulan’s lineup of outdoor lawn care equipment, specifically designed for those who require efficient and reliable grass cutting. This model stands out due to its powerful performance, user-friendly design, and advanced features that cater to both amateur gardeners and professional landscapers alike.

One of the main features of the PPR2042STA is its robust 42-inch cutting deck. This wide deck allows for efficient mowing of larger lawns without the need for excessive back-and-forth passes, thus reducing mowing time significantly. The deck is equipped with three high-performance blades, ensuring a clean and precise cut every time. With a cutting height adjustment feature, users can easily switch between different grass lengths, adapting to varying lawn conditions.

The PPR2042STA is powered by a 17.5 HP Briggs & Stratton engine, known for its reliability and performance. This engine delivers ample power to tackle thick grass and uneven terrains, making it suitable for diverse landscaping tasks. The automatic drive allows for a smooth operation, enabling users to navigate their lawns without the hassle of manual gear shifting.

Another standout technology integrated into the Poulan PPR2042STA is its innovative air induction mowing system. This system lifts the grass as it is cut, ensuring an even and consistent lawn appearance. Moreover, the mower’s design ensures effective grass discharge, whether utilizing the side discharge feature or connecting a mulching kit for finer grass clippings.

In terms of user comfort, the PPR2042STA boasts an ergonomic steering wheel and adjustable seat that ensures a comfortable ride, even during extended mowing sessions. The compact design of the mower, combined with its responsive controls, enhances maneuverability, making it easy to operate around flower beds, trees, and other obstacles.

Finally, the Poulan PPR2042STA features a durable steel frame that promises longevity, backed by a manufacturer's warranty that provides peace of mind to users. Maintenance is straightforward, with easy access to the engine and mower deck for cleaning and servicing.

With its powerful engine, efficient cutting system, and user-friendly design, the Poulan PPR2042STA represents excellent value for anyone looking to maintain their lawn effectively.
Top Page Image Contents