Poulan PPR2042STA To Remove Wheel for Repairs See Fig, To Start Engine with a Weak Battery

Page 22

SERVICE AND ADJUSTMENTS

TO REMOVE WHEEL FOR REPAIRS (See Fig. 25)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE

COVER

SQUARE KEY

(REAR WHEEL ONLY)

FIG. 25

TO START ENGINE WITH A WEAK BATTERY

WARNING: Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from bat- teries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Customer Responsibili- ties section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE (+) terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

FIG. 26

REPLACING BATTERY (See Figs. 27 and 28)

CAUTION: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from acciden- tal grounding.

•Lift seat pan to raised position.

•Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal.

•Connect BLACK grounding cable to negative (-) terminal with remaining hex bolt and keps nut. Tighten securely.

SEAT PAN

FIG. 27

TERMINAL

KEPS NUT

COVER

HEX

 

 

BOLT

POSITIVE (RED)

NEGATIVE

CABLE

(BLACK) CABLE

FIG. 28

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents PPR2042STA General Operation Safety RulesIV. Service II. Slope OperationTable of Contents Product Specifications Customer ResponsibilitiesSeat Unassembled HardwareSteering Wheel Slope Sheet KeysHOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig Check Tire Pressure To SET UP Your Mower for MulchingTo Convert to Bagging or Discharging Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills To Adjust Gauge Wheels See FigTo Operate Mower See Fig To TransportADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Mulching Mowing TipsCustomer Responsibilities General Recommendations Lubrication ChartBefore Each USE Tractor Engine Muffler CleaningAIR Filter See Fig Spark PlugsTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig To Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTo Adjust Steering Wheel Alignment To Adjust Brake See FigTransaxle Gear Shift Lever Neutral Adjustment See Fig To Replace Motion Drive Belt See FigTo Remove Wheel for Repairs See Fig To Start Engine with a Weak BatteryReplacing Battery See Figs To Attach Jumper CablesInterlocks and Relays To Adjust CarburetorTo Replace Headlight Bulb To Replace FuseFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionWhen operator leaves Schematic Tractor - Model Number PPR2042STAElectrical KEY Part Description Chassis Screw Hex Wshd 8-18 x 7/8 Drive 175410 Pulley Eng Steering Assembly KEY Part NO. NO. Description Seat Assembly Decals Wheels and TiresOptional Equipment EngineSpark Arrester 170771 Control Throt Mower Deck Washer, Spacer Mower Vented Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Service Notes C U M SEH Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

PPR2042STA specifications

The Poulan PPR2042STA is a notable addition to Poulan’s lineup of outdoor lawn care equipment, specifically designed for those who require efficient and reliable grass cutting. This model stands out due to its powerful performance, user-friendly design, and advanced features that cater to both amateur gardeners and professional landscapers alike.

One of the main features of the PPR2042STA is its robust 42-inch cutting deck. This wide deck allows for efficient mowing of larger lawns without the need for excessive back-and-forth passes, thus reducing mowing time significantly. The deck is equipped with three high-performance blades, ensuring a clean and precise cut every time. With a cutting height adjustment feature, users can easily switch between different grass lengths, adapting to varying lawn conditions.

The PPR2042STA is powered by a 17.5 HP Briggs & Stratton engine, known for its reliability and performance. This engine delivers ample power to tackle thick grass and uneven terrains, making it suitable for diverse landscaping tasks. The automatic drive allows for a smooth operation, enabling users to navigate their lawns without the hassle of manual gear shifting.

Another standout technology integrated into the Poulan PPR2042STA is its innovative air induction mowing system. This system lifts the grass as it is cut, ensuring an even and consistent lawn appearance. Moreover, the mower’s design ensures effective grass discharge, whether utilizing the side discharge feature or connecting a mulching kit for finer grass clippings.

In terms of user comfort, the PPR2042STA boasts an ergonomic steering wheel and adjustable seat that ensures a comfortable ride, even during extended mowing sessions. The compact design of the mower, combined with its responsive controls, enhances maneuverability, making it easy to operate around flower beds, trees, and other obstacles.

Finally, the Poulan PPR2042STA features a durable steel frame that promises longevity, backed by a manufacturer's warranty that provides peace of mind to users. Maintenance is straightforward, with easy access to the engine and mower deck for cleaning and servicing.

With its powerful engine, efficient cutting system, and user-friendly design, the Poulan PPR2042STA represents excellent value for anyone looking to maintain their lawn effectively.
Top Page Image Contents