Poulan PPR17H42STC To Replace Mower Blade Drive Belt See Fig, Belt Removal, Belt Installation

Page 20

SERVICE AND ADJUSTMENTS

SIDE-TO-SIDE ADJUSTMENT (See Figs. 20 and 21)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Three full turns of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE

 

BOTTOM EDGE

OF MOWER

 

OF MOWER

TO GROUND

 

TO GROUND

“A”

GROUND LINE

“A”

FIG. 20

SUSPENSION ARM

LIFT LINK ADJUSTMENT NUT

FIG. 21

FRONT-TO-BACK ADJUSTMENT (See Figs. 22 and 23)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO- SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length. Both links should be approximately 10-3/8".

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

• Recheck side-to-side adjustment.

20

MANDREL

"D"

"D"

FIG. 22

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT "E"

NUT "F"

TRUNNION

FRONT LINKS

FIG. 23

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 24)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Remove mower from tractor (See “TO REMOVE MOWER” in this section of this manual).

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Install new belt in reverse order of removal.

•Make sure belt is in all pulley grooves and inside all belt guides.

•Install mower in reverse order of removal instructions.

IDLER

PULLEYS

MANDREL

PULLEYS

FIG. 24

Page 19 Page 21
Image 20
Page 19 Page 21
Contents PPR17H42STC Safety Rules Safe Operation Practices for Ride-On MowersBecome ALERT!!! Your Safety is IN- Volved Table of Contents Unassembled Parts Steering Wheel SeatBlades Gauge WheelsAssembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig To SET UP Your Mower for MulchingTo Convert to Bagging or Discharging Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Adjust Mower Cutting Height See Fig Stopping See FigTo SET Parking Brake See Fig To USE Throttle Control See FigTo Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To Transport See FigsBefore Starting the Engine Check Engine OIL Level See FigADD Gasoline To Start Engine See FigMowing Tips Mulching Mowing Tips¿ Lubrication Chart Customer ResponsibilitiesGeneral Recommendations Before Each USETractor Brake OperationTires Operator Presence SystemEngine Spark Plugs CleaningMuffler Service and Adjustments To Install Mower See FigTo Level Mower Housing To Remove Mower See FigBelt Removal Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Adjust Brake See Fig Transmission REMOVAL/REPLACEMENTTransaxle Motion Control Lever Neutral ADJUSTMENTSee Fig To Replace Motion Drive Belt See FigTo Adjust Steering Wheel Alignment To Start Engine with a Weak Battery See FigReplacing Battery See Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Replace Headlight BulbInterlocks and Relays To Replace FuseStorage OtherFuel System Engine OILTroubleshooting Points OFF NON-REMOVABLE Connections Removable SchematicTractor - Model Number PPR17H42STC Electrical KEY Part NO. NO.DESCRIPTION Chassis and Enclosures KEY Part Description Drive Repair Parts Steering Assembly KEY Part NO. NO.DESCRIPTION Seat Assembly Decals Wheels and TiresSpark Arrester EngineOptional Equipment KEY Part NO. NO.DESCRIPTION Mower Deck KEY Part Description Tractor Model Number PPR17H42STC Mower Lift159460 Wire Asm Inner/Sprg W/plunger LT Service Notes Service Notes Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Sighting GuideParts and Service

173284, PPR17H42STC specifications

The Poulan Pro PPR17H42STC is a versatile lawn tractor that is designed to deliver exceptional performance in maintaining your lawn and garden. This powerful machine offers a combination of advanced features, robust technology, and user-friendly characteristics, making it an ideal choice for both homeowners and landscape professionals.

One of the standout features of the Poulan Pro PPR17H42STC is its robust 17.5-horsepower Briggs & Stratton engine. This reliable engine provides ample power to tackle a variety of mowing tasks efficiently, ensuring that even thick grass and uneven terrain are no match for its performance. Coupled with a hydrostatic transmission, this lawn tractor offers smooth acceleration and easy maneuverability, allowing the operator to navigate tight corners and challenging landscapes with ease.

The PPR17H42STC also boasts a 42-inch reinforced cutting deck, which is designed for durability and strength while delivering a professional-quality cut. The deck features a side-discharge capability, enabling the user to disperse clippings evenly across the lawn, promoting healthy grass growth. Additionally, the cutting height can be easily adjusted to suit varying lawn conditions, making it adaptable to changing seasons and grass types.

Another notable characteristic of this model is its ergonomic design, which includes a comfortable seat and user-friendly control layout. The high back seat provides support during longer mowing sessions, while the pedal-operated controls are intuitive, ensuring that users can focus on mowing without struggling with complicated mechanisms.

In terms of technology, the PPR17H42STC is equipped with a range of innovations aimed at enhancing the mowing experience. The integrated headlights provide improved visibility during early morning or late evening mowing sessions, while the easy-to-use ignition switch allows for quick and hassle-free starting.

Furthermore, this lawn tractor features a built-in mulching capability, allowing users to recycle grass clippings back into the lawn. This not only reduces yard waste but also provides essential nutrients to the soil, fostering a healthier lawn.

In summary, the Poulan Pro PPR17H42STC is a powerful, efficient, and user-friendly lawn tractor that combines advanced technology with practical features. Whether you are maintaining a small garden or a large lawn, this machine is designed to meet your needs effectively.
Top Page Image Contents