Poulan PK20H42YT manual Transmission REMOVAL/REPLACEMENT, To Adjust Steering Wheel ALIGN- Ment

Page 22

SERVICE AND ADJUSTMENTS

•Hold motion control lever in that position and turn engine off.

•While holding motion control lever in place, loosen the adjustment bolt.

•Move motion control lever to the neutral (N) (lock gate) position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

•Loosen the adjustment bolt.

•Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

•Tighten adjustment bolt securely.

•Start engine and test.

•If tractor still creeps, repeat above steps until satis- fied.

MOTION CONTROL

NEUTRAL

LEVER

LOCK GATE

 

ADJUSTMENT

BOLT

FIG. 24

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and beforeoperatingthetractor. See“PURGETRANSMISSION” in the Operation section of this manual.

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 25)

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 25

TO START ENGINE WITH A WEAK BATTERY (See Fig. 26)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

• Block up axle securely.

• Remove axle cover, retaining ring and washers to allow

wheel removal (rear wheel contains a square key - Do

not lose).

• Repair tire and reassemble.

• On rear wheels only: align grooves in rear wheel hub

and axle. Insert square key.

• Replace washers and snap retaining ring securely in

axle groove.

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

• Replace axle cover.

22

FIG. 26

Page 21 Page 23
Image 22
Page 21 Page 23
Contents PK20H42YT ModelGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Key Unassembled PartsSteering Wheel Seat Slope SheetTo Remove Tractor from CAR- TON AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig Assemble Gauge Wheels to Mower Deck See FigCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS Using the Reverse Operation SystemTo Operate Mower See Fig To Operate on HillsCheck Engine OIL Level Before Starting the EngineTo Transport See Figs ADD GasolinePurge Transmission Always operate engine at full throttle when mowMowing Tips Automatic Transmission Warm UPLubrication Chart MaintenanceMaintenance Schedule General RecommendationsBlade Removal See Fig TractorTo Sharpen Blade See Fig Engine Cleaning To Level Mower Housing Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigTo Replace Mower Blade Drive Belt See Fig Belt InstallationBelt Removal To Adjust Brake To Check and Adjust Brake See FigTransaxle Motion Control Lever Neutral Adjustment See Fig To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace FuseFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty L5V 3E4Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Fold Along This Dotted Line Degree SlopeParts and Service Changere DE Pièces LES ET L’ENTRETIEN Degrés Suivant LES UNE Pliez EST CeciDentretien Notes Autorisé Garantie cette de exclus sont normal l’entretien etDépannage DE Guide Correction Cause ProblèmeLame de mandrin le Remplacez Tordu est lame de mandrin Un Entreposage Reglages ET Revision Starter DU Commande LA Régler PourGAZ DES Commande LA DE Câble LE Régler Pour Carburateur LE Régler PourAVANT/ Roues DES Convergence LA DE ENLEVEMENT/REMPLACEMENTCarrossage LA DE L’ALIGNEMENT Régler PourFrein LE Régler ET Contrôler Pour Fig la VoirCourroie LA Remplacer Pour Tranmission DE MENTNETRAÎD’ENCourroie Acer Rempl Pour Tondeuse DE Lame DE MENTNETRAÎD’ENTondeuse LA Enlever Pour Tondeuse LA Installer PourTondeuse DE Boîtier LE Niveler Pour 16 .FIGAIR À Filtre Entretien’ALLUMAGE Bougie ’AIR Tamis LE NettoyerSionmistrans LA DE Moteur Fluide MoteurLubrification Transmission LA DE RefroidissementLames DES Entretien Fig la Voir Lame LA AffilerFig la Voir Lame LA Enlever EN Fonctionnement DE Système ETUtilisation Chaque Avant Générales Recommandations LESLubrification DE Tableau SUR Graisse DE NI D’HUILE NI Mettez NE Important10 .FIG UtilisationTransmission LA Purger QuetimaautoMoteur LE Démarrer DE Avant Accessoires Autres ET Charrettes DES Remorquer PourEt 5 .Fig les Voir Arrière Marche EN Fonctionnement Pentes LES Dans Utiliser PourTondeuse LA Utiliser Pour Jauge DE Roues LES Régler Pour GAZ DES Commande LA Utiliser PourTeurtrac Votre Utiliser Comment Fig la Voir Arrêter PourTracteur Votre Connaissez Propriété la de lendommagement Montage Desmancom Desmancom des tionfonc la etLA DE Tracteur LE Retirer Pour Des fonction la et mentceplalem connaîtreTionrecdi DE Volant LE Fixer Fig la Voir Siège LE InstallerDU Tracteur LE Sortir Pour Carton LE DeballezClés Montées NON PiécesPente-Guide Siège Direction de VolantSommaire En l’utilisation pour Conseils Général EntretienTracteurs des sécurité toute ’ESSENCE DE Sûre ManipulationTracteurs des sécurité toute en l’utilisation pour Conseils LES Dans Fonctionnement’éboule bord le si précipiter de ou bord Pelouse DE Tracteur PK20H42YT Modèle Propriétaire DU Manuel

PK20H42YT specifications

The Poulan PK20H42YT is a robust and reliable riding lawn mower designed to tackle a variety of lawn care needs. Equipped with a powerful engine and advanced features, this model is ideal for homeowners who seek efficiency and quality in their lawn maintenance.

At the heart of the PK20H42YT is a 20-horsepower Briggs & Stratton engine, which serves as the powerhouse for its cutting capabilities. This engine provides ample torque and speed, allowing the mower to handle thicker grass and uneven terrains with ease. The engine is designed for durability and longevity, ensuring that homeowners can count on consistent performance season after season.

One of the striking features of the Poulan PK20H42YT is its cutting deck, which measures 42 inches in width. This wide deck allows for more efficient mowing, significantly reducing the time required to cover large areas of lawn. The deck is made from heavy-duty materials, providing sturdiness while also ensuring that it can withstand the rigors of regular use.

The PK20H42YT also incorporates a quality cutting system that offers multiple height adjustments. This feature allows users to customize the cutting height based on their lawn's specific needs, whether it’s a manicured finish or a more rugged look. The mower also supports side discharge, mulching, and bagging options, giving homeowners flexibility in how they wish to manage their grass clippings.

Technologically, the Poulan PK20H42YT comes with an easy-to-use hydrostatic transmission, which provides a seamless driving experience. This transmission allows for smooth changes in speed without the need for gear shifting, making it user-friendly for operators of all experience levels. The mower also features a tight turning radius, enhancing maneuverability, especially in gardens with tight corners.

Additionally, the PK20H42YT includes comfort-enhancing features such as an adjustable seat and ergonomic steering for prolonged use without discomfort. The optimized layout of controls makes operation straightforward, allowing users to focus on mowing rather than fumbling with complicated machinery.

In summary, the Poulan PK20H42YT is designed for those who value performance, durability, and ease of use in lawn care equipment. With its powerful engine, versatile cutting options, and user-friendly features, it stands out as a reliable choice for maintaining a beautiful lawn all season long.
Top Page Image Contents