Poulan PK20H42YT manual Check Battery See Fig, Assemble Gauge Wheels to Mower Deck See Fig

Page 7

ASSEMBLY

SEAT SHOULDER

BOLT

SEAT PAN

466

FLAT WASHER

02464

ADJUSTMENT

KNOB

FIG. 2

CHECK BATTERY (See Fig. 3)

•Lift hood to raised position.

•If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in Maintenance section of this manual for charging instructions).

LABEL

0

2

1

73

 

 

 

 

 

FIG. 3

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

TO ROLL TRACTOR OFF SKID (See Op- eration section for location and function of controls)

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Release parking brake by depressing clutch/brake pedal.

•Place freewheel control in "transmission disengaged position" (See “TO TRANSPORT” in the Operation section of this manual).

•Roll tractor forward off skid.

•Remove banding holding the deflector shield up against tractor.

TO DRIVE TRACTOR OFF SKID (See Op- eration section for location and function of controls)

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

•Be sure all the above assembly steps have been com- pleted.

•Check engine oil level and fill fuel tank with gasoline.

•Place freewheel control in "transmission engaged" position (see "TO TRANSPORT" in Operation section of this manual).

•Sit on seat in operating position, depress clutch/brake pedal and set the parking brake.

•Place motion control lever in neutral (N) position.

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Start the engine. After engine has started, move throttle control to idle position.

•Release parking brake.

•Slowly move the motion control lever forward and slowly drive tractor off skid.

•Apply brake to stop tractor, set parking brake and place motion control lever in neutral position.

•Turn ignition key to "STOP" position.

Continue with the instructions that follow.

ASSEMBLE GAUGE WHEELS TO MOWER DECK (See Fig. 4)

The gauge wheels are designed to keep the mower deck in proper position when operating mower. Be sure they are properly adjusted to ensure optimum mower perfor-

mance.

•Slide gauge wheel bar down into bracket channel, Be sure that gauge wheel bar aligning holes are on top. Assemble gauge wheels as shown using shoulder bolts, 3/8 washers and 3/8-16 center locknuts and tighten securely.

•Adjust gauge wheels before operating mower. See “TO ADJUST GAUGE WHEELS” in the Operation section of this manual.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Model PK20H42YTII. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents Slope Sheet Unassembled PartsSteering Wheel Seat KeyBefore Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CAR- TONAssemble Gauge Wheels to Mower Deck See Fig Check Battery See FigCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills Using the Reverse Operation SystemTo Operate Mower See Fig Reverse Operation System ROSADD Gasoline Before Starting the EngineTo Transport See Figs Check Engine OIL LevelAutomatic Transmission Warm UP Always operate engine at full throttle when mowMowing Tips Purge TransmissionGeneral Recommendations MaintenanceMaintenance Schedule Lubrication ChartBlade Removal See Fig TractorTo Sharpen Blade See Fig Engine Cleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig Belt InstallationBelt Removal To Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTransaxle Motion Control Lever Neutral Adjustment See Fig To Adjust BrakeFront Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment To Start Engine with a Weak Battery See FigTo Replace Fuse To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsEngine dies when L5V 3E4 Limited WarrantyService Notes Fold Along This Dotted Line Degree Slope Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service Changere DE Pièces LES ET L’ENTRETIEN UNE Pliez EST Ceci Degrés Suivant LESDentretien Notes Garantie cette de exclus sont normal l’entretien et AutoriséCorrection Cause Problème Dépannage DE GuideLame de mandrin le Remplacez Tordu est lame de mandrin Un Entreposage Carburateur LE Régler Pour Starter DU Commande LA Régler PourGAZ DES Commande LA DE Câble LE Régler Pour Reglages ET RevisionLA DE L’ALIGNEMENT Régler Pour LA DE ENLEVEMENT/REMPLACEMENTCarrossage AVANT/ Roues DES ConvergenceTranmission DE MENTNETRAÎD’EN Fig la VoirCourroie LA Remplacer Pour Frein LE Régler ET Contrôler PourTondeuse DE Lame DE MENTNETRAÎD’EN Courroie Acer Rempl Pour16 .FIG Tondeuse LA Installer PourTondeuse DE Boîtier LE Niveler Pour Tondeuse LA Enlever Pour’AIR Tamis LE Nettoyer Entretien’ALLUMAGE Bougie AIR À FiltreTransmission LA DE Refroidissement MoteurLubrification Sionmistrans LA DE Moteur FluideEN Fonctionnement DE Système ET Fig la Voir Lame LA AffilerFig la Voir Lame LA Enlever Lames DES EntretienSUR Graisse DE NI D’HUILE NI Mettez NE Important Générales Recommandations LESLubrification DE Tableau Utilisation Chaque AvantQuetimaauto UtilisationTransmission LA Purger 10 .FIGMoteur LE Démarrer DE Avant Accessoires Autres ET Charrettes DES Remorquer PourEt 5 .Fig les Voir Arrière Marche EN Fonctionnement Pentes LES Dans Utiliser PourTondeuse LA Utiliser Pour Fig la Voir Arrêter Pour GAZ DES Commande LA Utiliser PourTeurtrac Votre Utiliser Comment Jauge DE Roues LES Régler PourTracteur Votre Connaissez Propriété la de lendommagement Montage Des fonction la et mentceplalem connaître Desmancom des tionfonc la etLA DE Tracteur LE Retirer Pour DesmancomCarton LE Deballez Fig la Voir Siège LE InstallerDU Tracteur LE Sortir Pour Tionrecdi DE Volant LE FixerSiège Direction de Volant Montées NON PiécesPente-Guide ClésSommaire ’ESSENCE DE Sûre Manipulation Général EntretienTracteurs des sécurité toute En l’utilisation pour ConseilsTracteurs des sécurité toute en l’utilisation pour Conseils LES Dans Fonctionnement’éboule bord le si précipiter de ou bord Pelouse DE Tracteur PK20H42YT Modèle Propriétaire DU Manuel

PK20H42YT specifications

The Poulan PK20H42YT is a robust and reliable riding lawn mower designed to tackle a variety of lawn care needs. Equipped with a powerful engine and advanced features, this model is ideal for homeowners who seek efficiency and quality in their lawn maintenance.

At the heart of the PK20H42YT is a 20-horsepower Briggs & Stratton engine, which serves as the powerhouse for its cutting capabilities. This engine provides ample torque and speed, allowing the mower to handle thicker grass and uneven terrains with ease. The engine is designed for durability and longevity, ensuring that homeowners can count on consistent performance season after season.

One of the striking features of the Poulan PK20H42YT is its cutting deck, which measures 42 inches in width. This wide deck allows for more efficient mowing, significantly reducing the time required to cover large areas of lawn. The deck is made from heavy-duty materials, providing sturdiness while also ensuring that it can withstand the rigors of regular use.

The PK20H42YT also incorporates a quality cutting system that offers multiple height adjustments. This feature allows users to customize the cutting height based on their lawn's specific needs, whether it’s a manicured finish or a more rugged look. The mower also supports side discharge, mulching, and bagging options, giving homeowners flexibility in how they wish to manage their grass clippings.

Technologically, the Poulan PK20H42YT comes with an easy-to-use hydrostatic transmission, which provides a seamless driving experience. This transmission allows for smooth changes in speed without the need for gear shifting, making it user-friendly for operators of all experience levels. The mower also features a tight turning radius, enhancing maneuverability, especially in gardens with tight corners.

Additionally, the PK20H42YT includes comfort-enhancing features such as an adjustable seat and ergonomic steering for prolonged use without discomfort. The optimized layout of controls makes operation straightforward, allowing users to focus on mowing rather than fumbling with complicated machinery.

In summary, the Poulan PK20H42YT is designed for those who value performance, durability, and ease of use in lawn care equipment. With its powerful engine, versatile cutting options, and user-friendly features, it stands out as a reliable choice for maintaining a beautiful lawn all season long.
Top Page Image Contents