Poulan PK20H42YT manual Before Starting the Engine, To Transport See Figs, Check Engine OIL Level

Page 13

OPERATION

•Avoid stopping or changing speed on hills.

•If slowing is necessary, move throttle control lever to slower position.

•If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake.

•Move motion control lever to neutral (N) position.

IMPORTANT: THE MOTION CONTROL LEVER DOES NOT RETURN TO NEUTRAL (N) POSITION WHEN THE CLUTCH/ BRAKE PEDAL IS DEPRESSED.

•To restart movement, slowly release parking brake and clutch/brake pedal.

•Slowly move motion control lever to slowest setting.

•Make all turns slowly.

TO TRANSPORT (See Figs. 5 and 9)

When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor.

•Raise attachment lift to highest position with attachment lift control.

•Pull freewheel control out and down into the slot and release so it is held in the disengaged position.

•Do not push or tow tractor at more than two (2) MPH.

•To reengage transmission, reverse above procedure.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

Transmission Engaged

Transmission Disengaged

FIG. 9

TOWING CARTS AND OTHER ATTACHMENTS

Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your trac- tor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

The engine in your tractor has been shipped, from the factory, already filled with summer weight oil.

•Check engine oil with tractor on level ground.

13

•Pull up and remove oil fill cap/dipstick; wipe oil off. Re- insert the dipstick into the tube and push down firmly into place. Remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•For cold weather operation you should change oil for easier starting (See “OIL VISCOSITY CHART” in the Maintenance section of this manual).

•To change engine oil, see the Maintenance section in this manual.

ADD GASOLINE

•Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

IMPORTANT: WHEN OPERATING IN TEMPERATURES BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE GASOLINE TO HELP INSURE GOOD COLD WEATHER STARTING.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

TO START ENGINE (See Fig. 5)

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

•Be sure freewheel control is in the transmission engaged position.

•Sit on seat in operating position, depress clutch/brake pedal and set parking brake.

•Place motion control lever in neutral (N) position.

•Move attachment clutch to “DISENGAGED” position.

•Move throttle control to choke position.

NOTE: Before starting, read the warm and cold starting procedures below.

•Insert key into ignition and turn key clockwise to “START” position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, move throttle control to fast position, wait a few minutes and try again. If engine still does not start, move the throttle control back to the choke position and retry.

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Model PK20H42YTSafe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Steering Wheel Seat Unassembled PartsKey Slope SheetTools Required for Assembly AssemblyTo Remove Tractor from CAR- TON Before Removing Tractor from SkidAssemble Gauge Wheels to Mower Deck See Fig Check Battery See FigCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig Using the Reverse Operation SystemReverse Operation System ROS To Operate on HillsTo Transport See Figs Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips Always operate engine at full throttle when mowPurge Transmission Automatic Transmission Warm UPMaintenance Schedule MaintenanceLubrication Chart General RecommendationsBlade Removal See Fig TractorTo Sharpen Blade See Fig Engine Cleaning To Install Mower See Fig Service and AdjustmentsTo Level Mower Housing To Remove Mower See FigTo Replace Mower Blade Drive Belt See Fig Belt InstallationBelt Removal Transaxle Motion Control Lever Neutral Adjustment See Fig To Check and Adjust Brake See FigTo Adjust Brake To Replace Motion Drive Belt See FigTo Adjust Steering Wheel ALIGN- Ment Transmission REMOVAL/REPLACEMENTTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace FuseOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when L5V 3E4 Limited WarrantyService Notes Fold Along This Dotted Line Degree Slope Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service Changere DE Pièces LES ET L’ENTRETIEN UNE Pliez EST Ceci Degrés Suivant LESDentretien Notes Garantie cette de exclus sont normal l’entretien et AutoriséCorrection Cause Problème Dépannage DE GuideLame de mandrin le Remplacez Tordu est lame de mandrin Un Entreposage GAZ DES Commande LA DE Câble LE Régler Pour Starter DU Commande LA Régler PourReglages ET Revision Carburateur LE Régler PourCarrossage LA DE ENLEVEMENT/REMPLACEMENTAVANT/ Roues DES Convergence LA DE L’ALIGNEMENT Régler PourCourroie LA Remplacer Pour Fig la VoirFrein LE Régler ET Contrôler Pour Tranmission DE MENTNETRAÎD’ENTondeuse DE Lame DE MENTNETRAÎD’EN Courroie Acer Rempl PourTondeuse DE Boîtier LE Niveler Pour Tondeuse LA Installer PourTondeuse LA Enlever Pour 16 .FIG’ALLUMAGE Bougie EntretienAIR À Filtre ’AIR Tamis LE NettoyerLubrification MoteurSionmistrans LA DE Moteur Fluide Transmission LA DE RefroidissementFig la Voir Lame LA Enlever Fig la Voir Lame LA AffilerLames DES Entretien EN Fonctionnement DE Système ETLubrification DE Tableau Générales Recommandations LESUtilisation Chaque Avant SUR Graisse DE NI D’HUILE NI Mettez NE ImportantTransmission LA Purger Utilisation10 .FIG QuetimaautoMoteur LE Démarrer DE Avant Accessoires Autres ET Charrettes DES Remorquer PourEt 5 .Fig les Voir Arrière Marche EN Fonctionnement Pentes LES Dans Utiliser PourTondeuse LA Utiliser Pour Teurtrac Votre Utiliser Comment GAZ DES Commande LA Utiliser PourJauge DE Roues LES Régler Pour Fig la Voir Arrêter PourTracteur Votre Connaissez Propriété la de lendommagement Montage LA DE Tracteur LE Retirer Pour Desmancom des tionfonc la etDesmancom Des fonction la et mentceplalem connaîtreDU Tracteur LE Sortir Pour Fig la Voir Siège LE InstallerTionrecdi DE Volant LE Fixer Carton LE DeballezPente-Guide Montées NON PiécesClés Siège Direction de VolantSommaire Tracteurs des sécurité toute Général EntretienEn l’utilisation pour Conseils ’ESSENCE DE Sûre ManipulationTracteurs des sécurité toute en l’utilisation pour Conseils LES Dans Fonctionnement’éboule bord le si précipiter de ou bord Pelouse DE Tracteur PK20H42YT Modèle Propriétaire DU Manuel

PK20H42YT specifications

The Poulan PK20H42YT is a robust and reliable riding lawn mower designed to tackle a variety of lawn care needs. Equipped with a powerful engine and advanced features, this model is ideal for homeowners who seek efficiency and quality in their lawn maintenance.

At the heart of the PK20H42YT is a 20-horsepower Briggs & Stratton engine, which serves as the powerhouse for its cutting capabilities. This engine provides ample torque and speed, allowing the mower to handle thicker grass and uneven terrains with ease. The engine is designed for durability and longevity, ensuring that homeowners can count on consistent performance season after season.

One of the striking features of the Poulan PK20H42YT is its cutting deck, which measures 42 inches in width. This wide deck allows for more efficient mowing, significantly reducing the time required to cover large areas of lawn. The deck is made from heavy-duty materials, providing sturdiness while also ensuring that it can withstand the rigors of regular use.

The PK20H42YT also incorporates a quality cutting system that offers multiple height adjustments. This feature allows users to customize the cutting height based on their lawn's specific needs, whether it’s a manicured finish or a more rugged look. The mower also supports side discharge, mulching, and bagging options, giving homeowners flexibility in how they wish to manage their grass clippings.

Technologically, the Poulan PK20H42YT comes with an easy-to-use hydrostatic transmission, which provides a seamless driving experience. This transmission allows for smooth changes in speed without the need for gear shifting, making it user-friendly for operators of all experience levels. The mower also features a tight turning radius, enhancing maneuverability, especially in gardens with tight corners.

Additionally, the PK20H42YT includes comfort-enhancing features such as an adjustable seat and ergonomic steering for prolonged use without discomfort. The optimized layout of controls makes operation straightforward, allowing users to focus on mowing rather than fumbling with complicated machinery.

In summary, the Poulan PK20H42YT is designed for those who value performance, durability, and ease of use in lawn care equipment. With its powerful engine, versatile cutting options, and user-friendly features, it stands out as a reliable choice for maintaining a beautiful lawn all season long.
Top Page Image Contents