Poulan PD25PH48STA owner manual Service and Adjustments, To Remove Mower See Fig, To Install Mower

Page 20

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUST- MENTS:

•Depress clutch/brake pedal fully and set parking brake.

•Place motion control lever in neutral (N) position.

•Place attachment clutch in “DISENGAGED” position.

•Turn ignition key to “STOP” and remove key.

•Make sure the blades and all moving parts have completely stopped.

•Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TRACTOR

TO REMOVE MOWER (See Fig. 19)

•Place attachment clutch in “DISENGAGED” position.

•If equipped, turn height adjustment knob to lowest setting.

•Lower mower to its lowest position.

•Disengage belt tension rod from lock bracket.

CAUTION: Rod is spring loaded. Have a tight grip on rod and release slowly.

•Remove retainer spring holding anti-swaybar to chassis bracket and disengage anti-swaybar from bracket.

•Remove four retainer springs from front plate assembly and remove plate.

•Remove retainer springs from suspension arms at deck and disengage arms from deck.

•Raise attachment lift to its highest position.

•Slide mower forward and remove belt from electric clutch pulley.

•Slide mower out from under right side of tractor.

TO INSTALL MOWER

Be sure tractor is on level surface and mower suspension arms are raised with attachment lift control. Engage park- ing brake.

•Swing anti-sway bar to left side of mower deck.

•Slide mower under tractor with deflector shield to right side of tractor.

IMPORTANT: CHECK BELT FOR PROPER ROUTING IN ALL MOWER PULLEY GROOVES.

•If equipped, turn height adjustment knob counter- clockwise until it stops.

•Lower mower linkage with attachment lift control.

•Be sure belt tension rod is in disengaged position.

•Install belt into electric clutch pulley groove.

•Place the suspension arms on outward pointing deck pins. Retain with double loop retainer spring with loops up as shown.

•Install front plate assembly to tractor suspension brackets and retain with single loop retainer springs as shown.

SUSPENSION ARMS

LOCK BRACKET

 

 

BELT TENSION ROD

 

 

 

(DISENGAGED POSITION)

 

FRONT

ELECTRIC CLUTCH PULLEY

 

 

 

 

 

MOWER

FRONT PLATE

 

 

BRACKET

 

 

ASSEMBLY

 

 

 

CHASSIS

 

 

SINGLE LOOP

BRACKET

 

 

 

 

RETAINER

 

 

 

 

 

 

SPRING

 

 

 

DOUBLE LOOP

 

 

 

RETAINER

 

 

 

SPRING

RETAINER

 

 

 

SPRING

 

 

FLANGED PIN

 

ANTI-SWAY

 

 

USE PLIERS FOR

BAR

 

DEFLECTOR

RETAINER SPRINGS

 

 

SHIELD

 

SUSPENSION ARMS

 

 

 

DOUBLE LOOP

 

 

 

RETAINER SPRINGS

 

 

LOOP UP

(Outward pointing

 

 

deck pins)

 

02565

 

 

 

 

 

FIG. 19

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents PD25PH48STA Safety Rules Safety Rules Table of Contents Unassembled Parts Assembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig Assemble Gauge Wheels to Mower Deck See FigInstall Mower and Drive Belt See Figs To Attach Nose Roller See FigCheck Tire Pressure Check Mower LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To Transport See FigsBefore Starting the Engine Towing Carts and Other ATTACH- MentsCheck Engine OIL Level ADD GasolineAutomatic Transmission Warm UP Purge TransmissionMowing Tips Maintenance Lubrication ChartGeneral Recommendations Before Each USETractor Engine Cleaning Clean AIR INTAKE/COOLING AreasMuffler Spark PlugsTo Remove Mower See Fig Service and AdjustmentsTo Install Mower To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Check and Adjust Brake See Fig To Replace Mower Drive BeltTo Replace Mower Blade Drive Belt See Fig To Check BrakeTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel ALIGN- MentTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBERTo Start Engine with a Weak Battery See Fig Replacing Battery See FigTo Replace Headlight Bulb Interlocks and RelaysTo Remove Hood and Grill Assembly See Fig To Adjust Throttle Control Cable See FigTo Adjust Choke Control See Fig To Adjust CarburetorStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionWith attachment clutch Schematic Tractor Model Number PD25PH48STA, Product Number 954 56Electrical KEY Part Description Chassis and Enclosures Repair Parts Tractor Model Number PD25PH48STA, Product Number 954 56 Drive KEY Part NO. NO. DescriptionSteering Assembly 180656 Wheel Steering Engine KEY Part NO. NO. Description Seat Assembly Decals Wheels & TiresMower Lift KEY Part NO. NO. Description Mower Deck KEY Part Description Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Parts and Service

PD25PH48STA specifications

The Poulan PD25PH48STA is a robust and efficient riding lawn mower designed to provide an exceptional mowing experience for homeowners with large yards. This model strikes the perfect balance between power, performance, and user-friendly features, making it a favored choice for both novices and seasoned lawn care enthusiasts.

One of the standout features of the PD25PH48STA is its powerful 25 horsepower Briggs & Stratton engine. This reliable engine ensures that the mower can handle tough grass and varied terrain without compromising performance. The engine is known for its durability and low maintenance requirements, allowing users to focus more on mowing and less on upkeep.

The 48-inch cutting deck of the PD25PH48STA offers a wide cutting path, allowing for efficient mowing of large areas. The deck is constructed with high-quality materials that ensure longevity and resistance to wear. The adjustable cutting height feature allows users to customize the grass height according to their preferences, providing flexibility for different mowing conditions.

Another notable aspect of the Poulan PD25PH48STA is its hydrostatic transmission system. This technology allows for smooth and effortless operation, enabling users to easily adjust their speed without the need for shifting gears. This ease of use is particularly beneficial when navigating around obstacles or tackling sloped terrains.

In terms of comfort, the PD25PH48STA is equipped with a roomy and comfortable seat, designed to support prolonged use without discomfort. The intuitive control layout enhances user experience, allowing operators to access necessary functions quickly and efficiently.

The mower is also designed with an innovative cutting system that ensures even grass distribution. Its high-performance blades deliver a clean and consistent cut, promoting a healthier lawn.

For convenience, the PD25PH48STA features a simple to use start mechanism making it reliable in various weather and operational conditions. Its compact design allows for easy maneuverability around flower beds and other landscaping features.

In summary, the Poulan PD25PH48STA is a powerful riding lawn mower that combines robust performance with user-friendly features. With its efficient Briggs & Stratton engine, wide cutting deck, hydrostatic transmission, and emphasis on comfort and easy operation, this mower is an excellent investment for anyone looking to maintain their lawn with ease and precision.
Top Page Image Contents