Poulan PD25PH48STA owner manual To Level Mower Housing, FRONT-TO-BACK Adjustment See Figs

Page 21

SERVICE AND ADJUSTMENTS

•Position front plate assembly between front mower brackets. Raise deck and plate assembly to align holes and insert flanged pins. Secure pins with double loop retainer springs between the plate assembly and mower brackets.

NOTE: To assist in locating hole in flanged pin, the hole in pin is inline with notch on head of pin. If necessary, move mower side-to-side to give space between plate and mower brackets.

IMPORTANT: CHECK BELT FOR PROPER ROUTING IN ALL MOWER PULLEY GROOVES.

•Engage belt tension rod by pushing rod into locking bracket.

CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and engage slowly.

•Connect anti-sway bar to chassis bracket under left footrest and retain with double loop retainer spring.

•If equipped, turn height adjustment knob clockwise to remove slack from mower suspension.

•Raise deck to highest position.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PRODUCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 20 and 21)

•Raise mower to its highest position.

•Measure height from bottom edge of mower to ground level at front corners of mower. Distance “A” on both sides of mower should be the same.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

•Recheck measurements after adjusting.

BOTTOM EDGE

 

BOTTOM EDGE

OF MOWER TO

00598

OF MOWER TO

GROUND

 

GROUND

A

GROUND LINE

A

FIG. 20

SUSPENSION ARM

LIFT LINK ADJUSTMENT NUT

01553

FRONT-TO-BACK ADJUSTMENT (See Figs. 22 and 23)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower blades should be adjusted so the front tip is approximately 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.

CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

Check adjustment on right side of tractor. Position any blade so the tip is pointing straight forward. Measure distance "B" at front and rear tip of the blade.

•Before making any necessary adjustments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of blade, loosen nut “C” on both front links an equal number of turns.

NOTE: Each full turn of nut “C” will change distance. “B” by approximately 3/16".

•When distance “B” is 1/8" to 1/2" lower at front than rear, tighten nut “D” against trunnion on both front links.

•To raise front of blade, loosen nut “D” from trunnion on both front links. Tighten nut “C” on both front links an equal number of turns.

•When distance “B” is 1/8" to 1/2" lower at front than rear, tighten nut “D” against trunnion on both front links.

•Recheck side-to-side adjustment.

02548

MANDREL

“B”“B”

FIG. 22

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

02516

TRUNNION

NUT “D”

FRONT PLATE

NUT “C”

02517

ASSEMBLY

 

FIG. 21

FIG. 23

 

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents PD25PH48STA Safety Rules Safety Rules Table of Contents Unassembled Parts Tools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonAssemble Gauge Wheels to Mower Deck See Fig Install Seat See FigTo Attach Nose Roller See Fig Install Mower and Drive Belt See FigsCheck Mower Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsTowing Carts and Other ATTACH- Ments Before Starting the EngineCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP Lubrication Chart MaintenanceGeneral Recommendations Before Each USETractor Engine Clean AIR INTAKE/COOLING Areas CleaningMuffler Spark PlugsService and Adjustments To Install MowerTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Drive Belt To Check and Adjust Brake See FigTo Replace Mower Blade Drive Belt See Fig To Check BrakeTo Adjust Steering Wheel ALIGN- Ment Transmission REMOVAL/REPLACEMENTTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBERReplacing Battery See Fig To Start Engine with a Weak Battery See FigTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Throttle Control Cable See Fig To Remove Hood and Grill Assembly See FigTo Adjust Choke Control See Fig To Adjust CarburetorOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsWith attachment clutch Tractor Model Number PD25PH48STA, Product Number 954 56 SchematicElectrical KEY Part Description Chassis and Enclosures Repair Parts Tractor Model Number PD25PH48STA, Product Number 954 56 KEY Part NO. NO. Description DriveSteering Assembly 180656 Wheel Steering Engine KEY Part NO. NO. Description Seat Assembly Wheels & Tires DecalsMower Lift KEY Part NO. NO. Description Mower Deck KEY Part Description Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Parts and Service

PD25PH48STA specifications

The Poulan PD25PH48STA is a robust and efficient riding lawn mower designed to provide an exceptional mowing experience for homeowners with large yards. This model strikes the perfect balance between power, performance, and user-friendly features, making it a favored choice for both novices and seasoned lawn care enthusiasts.

One of the standout features of the PD25PH48STA is its powerful 25 horsepower Briggs & Stratton engine. This reliable engine ensures that the mower can handle tough grass and varied terrain without compromising performance. The engine is known for its durability and low maintenance requirements, allowing users to focus more on mowing and less on upkeep.

The 48-inch cutting deck of the PD25PH48STA offers a wide cutting path, allowing for efficient mowing of large areas. The deck is constructed with high-quality materials that ensure longevity and resistance to wear. The adjustable cutting height feature allows users to customize the grass height according to their preferences, providing flexibility for different mowing conditions.

Another notable aspect of the Poulan PD25PH48STA is its hydrostatic transmission system. This technology allows for smooth and effortless operation, enabling users to easily adjust their speed without the need for shifting gears. This ease of use is particularly beneficial when navigating around obstacles or tackling sloped terrains.

In terms of comfort, the PD25PH48STA is equipped with a roomy and comfortable seat, designed to support prolonged use without discomfort. The intuitive control layout enhances user experience, allowing operators to access necessary functions quickly and efficiently.

The mower is also designed with an innovative cutting system that ensures even grass distribution. Its high-performance blades deliver a clean and consistent cut, promoting a healthier lawn.

For convenience, the PD25PH48STA features a simple to use start mechanism making it reliable in various weather and operational conditions. Its compact design allows for easy maneuverability around flower beds and other landscaping features.

In summary, the Poulan PD25PH48STA is a powerful riding lawn mower that combines robust performance with user-friendly features. With its efficient Briggs & Stratton engine, wide cutting deck, hydrostatic transmission, and emphasis on comfort and easy operation, this mower is an excellent investment for anyone looking to maintain their lawn with ease and precision.
Top Page Image Contents