Poulan CO185H42STC manual Tractor

Page 18

TRACTOR

Always observe safety rules when per- forming any maintenance.

BRAKE OPERATION

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp

objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are working properly. If your trac- tor does not function as described, repair the problem immediately.

•The engine should not start unless the brake pedal is fully depressed and attachement clutch control is in the disengaged position.

•When the engine is running, any at- tempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any at- tempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never op- erate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

BLADE REMOVAL

1.Raise mower to highest position to al- low access to blades.

2.Remove blade bolt, lock washer and flat washer securing blade.

3.Install new or resharpened blade with

trailing edge up towards deck as shown. IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly.

4.Reassemble blade bolt, lock washer and flat washer in exact order as shown.

5.Tighten blade bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: Blade bolt is heat treated. If bolt needs replacing, replace only with approve bolt shown in the Repair Parts.

Flat

Trailing Edge Up

 

 

Mandrel

 

 

2

 

0

14

 

 

Blade

1

 

Assembly

Washer

 

 

 

 

 

 

Lock

 

 

 

 

Washer

 

 

 

 

Blade

 

 

 

Star

 

 

 

 

Bolt

Center Hole

 

 

 

TO SHARPEN BLADE

NOTE: We do not recommend sharp- ening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An unbalanced blade will cause excessive vibration and eventual damage to mower and engine.

•The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone bal- ancer. (When using a cone balancer, follow the instructions supplied with balancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

 

 

Center

5/8" Bolt

01202

Hole

 

or Pin

Blade

 

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. How- ever, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour. NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and termi- nals can cause the battery to “leak” power. 1. Remove terminal guard.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Model NO. CO185H42STC Table of Contents WarrantySafety Rules General OperationII. Slope Operation IV. Service III. ChildrenDo not Safety Rules Product Specifications Customer ResponsibilitiesAPI-SG-SL Unassembled Parts Tools Required for Assembly To Remove Tractor from CartonBefore Removing Tractor from Skid Install Mulcher Plate If previously removed Reposition Right Rear Gauge Wheel ChecklistTo Convert to Bagging or Discharging Check Tire PressureOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower To Operate on HillsTo Transport Towing Carts and Other ATTACH- Ments Before Starting the EngineTo Start Engine Check Engine OIL LevelMowing Tips Mulching Mowing TipsAutomatic Transmission Warm UP Maintenance General RecommendationsBefore Each USE Tractor Engine Service and Adjustments CleaningSIDE-TO-SIDE Adjustment To Install MowerTo Level Mower Housing FRONT-TO-BACK AdjustmentTo Check and Adjust Brake To Replace Mower Blade Drive BeltTo Replace Motion Drive Belt To Start Engine with a Weak Battery Transaxle Motion Control LE- VER Neutral AdjustmentTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor Fuel System BatteryOther Engine OILTroubleshooting Chart Problem Cause CorrectionExcessive Poor grass Suggested Guide for Sighting Slopes for Safe Operation

CO185H42STC specifications

The Poulan CO185H42STC is a robust and versatile lawn tractor that has become a favored choice for homeowners seeking an efficient and reliable grass-cutting machine. With its powerful engine and efficient design, the CO185H42STC is equipped to handle both small and large lawns with ease.

One of the standout features of the Poulan CO185H42STC is its reliable engine. Powered by an 18.5 horsepower Briggs & Stratton engine, this lawn tractor is built for performance. The engine design ensures optimal power delivery, allowing for smooth operation while navigating various terrains. The automatic choke system further enhances user convenience, ensuring that the lawn tractor starts easily in all weather conditions.

The cutting deck of the CO185H42STC spans an impressive 42 inches, which allows users to cover large areas in a shorter amount of time. The deck is constructed using durable materials that can withstand wear and tear, ensuring longevity. The tractor also features an adjustable cutting height, offering six different positions between 1.5 inches to 4 inches, providing flexibility to achieve the desired lawn finish.

A notable technology included in this model is the hydrostatic transmission system. Unlike the traditional gear system, this advanced transmission allows for smooth speed changes without the need for gear shifting, enabling a more enjoyable driving experience. This feature is especially beneficial when navigating around obstacles or when mowing uneven terrain.

Comfort is another key aspect of the Poulan CO185H42STC. The tractor is equipped with a high-back seat that provides excellent support during extended mowing sessions. The ergonomic steering wheel maximizes maneuverability and is designed to minimize operator fatigue, ensuring a comfortable ride.

The CO185H42STC also includes a convenient bagging attachment, which allows for easy collection of clippings, making yard cleanup quick and efficient. Additionally, its rugged construction means it can handle challenging mowing tasks without the risk of damage.

In summary, the Poulan CO185H42STC is a highly capable lawn tractor that combines power, technology, and user-friendly features. Ideal for homeowners looking to maintain a pristine lawn, it stands out with its powerful engine, adjustable cutting deck, hydrostatic transmission, and focus on operator comfort. This lawn tractor offers a perfect blend of performance and convenience, making it a noteworthy addition to any lawn care toolkit.
Top Page Image Contents