Poulan CN1842STA manual To Adjust Carburetor

Page 24

REPLACING BATTERY

WARNING: Do not short battery ter- minals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, re- move metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from accidental grounding.

1.Lift seat pan to raised position.

2.Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

3.Install new battery with terminals in same position as old battery.

4.First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal

5.Connect BLACK grounding cable to negative (-) terminal with remaining hex bolt and keps nut. Tighten se- curely.

Seat Pan

 

02602

Terminal Cover

Keps Nut

 

Hex

 

Bolt

Positive

 

(Red) 02603

 

Cable

Negative

 

(Black) Cable

TO REPLACE HEADLIGHT BULB

1.Raise hood.

2.Pull bulb holder out of the hole in the backside of the grill.

3.Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

4.Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL AS- SEMBLY

1.Raise hood.

2.Unsnap headlight wire connector.

3.Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

4.When replacing hood, be sure to re- connect the headlight wire connector.

Hood

Headlight

 

Wire

 

Connector

 

01536

ENGINE

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be nec- essary. Check adjustment as described below before loosening cable. If adjust- ment is necessary, see engine manual

TO ADJUST CARBURETOR

The carburetor has been preset at the factory and adjustment should not be nec- essary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, see engine manual.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Model NO. CN1842STA Table of Contents WarrantySafety Rules General OperationII. Slope Operation IV. Service III. ChildrenDo not Safety Rules Product Specifications Customer ResponsibilitiesAPI-SF-SJ Unassembled Parts Tools Required for Assembly HOW to SET UP Your TractorTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery Install Mulcher Plate To Convert to Bagging or DischargingCheck Tire Pressure Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine To Start Engine Mowing TipsMaintenance General RecommendationsBefore Each USE Tractor Engine Cleaning MufflerSpark Plugs IN-LINE Fuel FilterService and Adjustments To Install MowerTo Remove Mower To Level Mower Housing SIDE-TO-SIDE AdjustmentTo Check and Adjust Brake To Replace Mower Blade Drive BeltTo Replace Motion Drive Belt To Adjust Steering Wheel ALIGN- Ment To Start Engine with a Weak BatteryFront Wheel TOE-IN/CAMBER To Remove Wheel for RepairsTo Adjust Carburetor Battery OtherFuel System Engine OILTroubleshooting Chart Problem Cause CorrectionExcessive Poor grass Suggested Guide for Sighting Slopes for Safe Operation

CN1842STA specifications

The Poulan CN1842STA is a versatile and reliable riding lawn mower designed to make lawn care efficient and straightforward. With its robust features and reliable performance, this mower is ideal for homeowners with medium to large-sized lawns.

One of the standout features of the Poulan CN1842STA is its powerful 18.5 HP Briggs & Stratton engine. This engine provides ample power for cutting through thick grass and tackling uneven terrain. The easy-starting engine ensures that users spend less time preparing and more time mowing.

The cutting deck of the CN1842STA is a 42-inch wide design, which allows for a larger cutting path while maintaining maneuverability around obstacles. The deck height can be easily adjusted to suit various grass lengths, providing flexibility in lawn care. With a cutting height range of 1 to 4 inches, users can customize their lawn treatment according to seasonal needs.

Another attractive aspect of this riding mower is its hydrostatic transmission. Unlike traditional gear-driven mowers, the hydrostatic transmission allows for smooth, effortless speed changes. This makes it easier to navigate tight spots or slow down for detailed trimming work.

The Poulan CN1842STA also features a comfortable high-back seat designed to reduce fatigue during long mowing sessions. The steering wheel is ergonomically designed, offering users excellent control and maneuverability. Moreover, the intuitive dashboard provides essential information at a glance, ensuring the operator can monitor performance without losing focus on the task.

Built with durability in mind, the CN1842STA features a rugged frame and strong chassis, designed to withstand the rigors of outdoor use. The mower's design incorporates a reinforced cutting deck, ensuring it can handle tough mowing conditions without compromising performance.

The Poulan CN1842STA is also equipped with ease of maintenance in mind. Access points for the engine and cutting deck are designed for convenience, allowing for quick oil changes and blade sharpening.

Overall, the Poulan CN1842STA offers an excellent blend of power, comfort, and reliability, making it a valuable asset for anyone looking to maintain a well-manicured lawn with minimal effort. With its combination of user-friendly features and robust technology, this riding mower stands out as a top choice for lawn care enthusiasts.
Top Page Image Contents