Poulan CN1842STA manual To Adjust Steering Wheel ALIGN- Ment, Front Wheel TOE-IN/CAMBER

Page 23

Engine

Pulley

Clutching

Idler

Stationary

Idler

Center

Span

Keeper

Transaxle

Pulley

00811

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not

horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble with crossbars horizontal. Tighten securely.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS

1.Block up axle securely.

2.Remove axle cover, retaining ring and washers to allow wheel removal (rear wheels have a square key - Do not lose).

3.Repair tire and reassemble.

NOTE: On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

4.Replace washers and snap retaining ring securely in axle groove.

5.Replace axle cover.

Washers

Retaining

Ring

Axle

Cover

Square Key

(Rear Wheel Only)

TO START ENGINE WITH A WEAK BATTERY

WARNING: Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the en- gine, it should be recharged. (See "BAT- TERY" in the MAINTENANCE section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure: IMPORTANT: Your tractor is equipped with a 12 volt system. The other vehicle must also be a 12 volt system. Do not use your tractor battery to start other vehicles.

TO ATTACH JUMPER CABLES -

1.Connect one end of the RED cable to the POSITIVE (+) terminal of each battery(A-B), taking care not to short against tractor chassis.

2.Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

3.Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

1.BLACK cable first from chassis and then from the fully charged battery.

2.RED cable last from both batteries.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

Weak or Dead Battery

02614

Fully Charged Battery

23

Image 23
Contents Model NO. CN1842STA Warranty Table of ContentsII. Slope Operation Safety RulesGeneral Operation Do not IV. ServiceIII. Children Safety Rules API-SF-SJ Product SpecificationsCustomer Responsibilities Unassembled Parts Before Removing Tractor from Skid Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonCheck Battery Check for Proper Position of ALL Belts Install Mulcher PlateTo Convert to Bagging or Discharging Check Tire PressureOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine Mowing Tips To Start EngineBefore Each USE MaintenanceGeneral Recommendations Tractor Engine IN-LINE Fuel Filter CleaningMuffler Spark PlugsTo Remove Mower Service and AdjustmentsTo Install Mower SIDE-TO-SIDE Adjustment To Level Mower HousingTo Replace Motion Drive Belt To Check and Adjust BrakeTo Replace Mower Blade Drive Belt To Remove Wheel for Repairs To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery Front Wheel TOE-IN/CAMBERTo Adjust Carburetor Engine OIL BatteryOther Fuel SystemProblem Cause Correction Troubleshooting ChartExcessive Poor grass Suggested Guide for Sighting Slopes for Safe Operation

CN1842STA specifications

The Poulan CN1842STA is a versatile and reliable riding lawn mower designed to make lawn care efficient and straightforward. With its robust features and reliable performance, this mower is ideal for homeowners with medium to large-sized lawns.

One of the standout features of the Poulan CN1842STA is its powerful 18.5 HP Briggs & Stratton engine. This engine provides ample power for cutting through thick grass and tackling uneven terrain. The easy-starting engine ensures that users spend less time preparing and more time mowing.

The cutting deck of the CN1842STA is a 42-inch wide design, which allows for a larger cutting path while maintaining maneuverability around obstacles. The deck height can be easily adjusted to suit various grass lengths, providing flexibility in lawn care. With a cutting height range of 1 to 4 inches, users can customize their lawn treatment according to seasonal needs.

Another attractive aspect of this riding mower is its hydrostatic transmission. Unlike traditional gear-driven mowers, the hydrostatic transmission allows for smooth, effortless speed changes. This makes it easier to navigate tight spots or slow down for detailed trimming work.

The Poulan CN1842STA also features a comfortable high-back seat designed to reduce fatigue during long mowing sessions. The steering wheel is ergonomically designed, offering users excellent control and maneuverability. Moreover, the intuitive dashboard provides essential information at a glance, ensuring the operator can monitor performance without losing focus on the task.

Built with durability in mind, the CN1842STA features a rugged frame and strong chassis, designed to withstand the rigors of outdoor use. The mower's design incorporates a reinforced cutting deck, ensuring it can handle tough mowing conditions without compromising performance.

The Poulan CN1842STA is also equipped with ease of maintenance in mind. Access points for the engine and cutting deck are designed for convenience, allowing for quick oil changes and blade sharpening.

Overall, the Poulan CN1842STA offers an excellent blend of power, comfort, and reliability, making it a valuable asset for anyone looking to maintain a well-manicured lawn with minimal effort. With its combination of user-friendly features and robust technology, this riding mower stands out as a top choice for lawn care enthusiasts.