Poulan 968999302 manual Cleaning and Washing, Caster Wheels, Hardware, Caster bolt

Page 52

MAINTENANCE

Cleaning and Washing

Regular cleaning and washing, especially under the mower deck, will increase the machine’s lifespan. Make it a habit to clean the machine directly after use (after it is cooled), before the dirt sticks.

Do not spray water on the top of the mower deck. Use compressed air to clean the top side of mower deck. Regularly clean deck and underside of deck, avoid spraying engine and electrical components with water.

Use protective glasses when cleaning and washing.

Caster Wheels

Check every 200 hours. Lift front of unit off of ground so caster wheels can rotate freely. Tighten caster bolt then back off 1/2 turn. Check that wheel rotates freely. If wheel does not rotate freely back the caster bolt off in 1/4 turn increments until wheel rotates freely.

IMPORTANT INFORMATION

DO NOT add any type of tire liner or foam fill material to the tires. Excessive loads created by foam filled tires will cause premature failures.

Only use O.E.M. specified tires.

Foam filled tires or solid tires will void the warranty.

Hardware

Check daily. Inspect the entire machine for loose or missing hardware.

8011-644

Cleaning

1

1. Caster bolt

8011-619

Caster wheels

English-50

Image 52
Contents Pro 900 ZX Page Contents OPERATOR’S Manual Rider SeriesEnglish-2 Introduction IntroductionGood Service Manufacturing NumberSymbols and Decals Symbols and DecalsXxxx xxxxxx Objects Engine is Running Moving sharp blades under cover Safety Instructions Safety InstructionsGeneral Operation English-8 Personal Safety Equipment Slope OperationChildren Maintenance General Maintenance Risk of sparking Transport Important InformationCustomer responsibilities Controls ControlsControl Locations Motion Control Levers TrackingSeat adjustment knobs FusesBy pass linkages Blade switch RefuelingChoke Control Ignition SwitchThrottle Control Parking Brake Hour MeterMachine must be stopped before activating the parking brake Accessories Cutting height pedalOperation OperationTraining Before Starting Starting the EngineDepress the control for disengaging the mower deck Press in and turn the ignition key to the start position To start an engine with a weak battery To remove cables, reverse orderRunning Operating on hills Mowing Tips Stopping the Engine Moving by Hand Maintenance MaintenanceMaintenance Schedule = Described in this manual  = Not described in this manual Battery To clean battery and terminalsReplacing battery Always use protective glasses when handling the batteryIgnition System Checking the Safety System Checking and Adjusting the Choke Cable Checking and Adjusting the Throttle CableChecking the Engines Cooling Air Intake Replacing the Air Filter Briggs and Stratton engineFaulty adjustment can cause an accident Replacing the Fuel FilterChecking Tire Pressures Checking the Parking BrakeChecking the V-belts Deck beltDeck belt installation To replace EZT E-Series Zeroturn Transaxle belt EZT beltEZT belt removal Checking the Blades Check the bladesAdjusting the Mower Deck Side-to-side adjustment To level deckFront-to-back adjustment To adjust anti-scalp rollers Cleaning and Washing Use protective glasses when cleaning and washingCaster Wheels HardwareLubrication LubricationLubrication Schedule Lubricating the Cables Lubricating in Accordance with the Lubrication ScheduleCaster wheels Engine Oil Briggs & Stratton Changing the Engine OilOil drain valve Checking the oil level Changing the Oil FilterTransmission Trouble Shooting Guide Trouble Shooting GuideProblem Cause Wrong fuel type English-58 Service StorageStorage Winter StorageWiring Diagrams Wiring diagramTechnical Data Technical DataZ4822 Equipment Torque Specifications Conformity Certificates Conformity CertificatesUSA requirements Service Journal Service JournalDelivery Service Action Date, mtr reading, stamp, signAfter the First 5-8 Hours Hour Service English-68 English-69 English-70 At Least Once Each Year English-72 English-73 110192Rir12/19/05