Hitachi PJ-LC9 user manual Turning off the power

Page 22

Power on/off

Turning off the power

1. Press the STANDBY/ON button on the projector or the remote control.

The message "Power off?" will appear on the screen for approximately 5 seconds.

2. Press the STANDBY/ON button on the projector or the remote control again while the message appears.

The projector lamp will go off, and the POWER indicator will begin blinking in orange. Then the POWER indicator will stop blinking and light in steady orange when the lamp cooling is complete.

3. Make sure that the power indicator lights in steady orange, and set the power switch to the OFF position. The POWER indicator will go off. Do not set the power switch to the OFF position while the POWER indicator is green or blinking.

Power off?

POWER (Blinking in orange)

POWER (Steady orange)

POWER (Steady orange)

4. Close the lens cover. For safety purposes, disconnect the power cord if the projector is not to be used for prolonged periods of time.

NOTE • Turn the power off in right order. First power off the connected devices and then the projector.

Except for an emergency, whenever you turn the projector off, obey the procedure of the following “Turning off the power”, and do not disconnect the power cord until the procedure is completed. Neglect causes a damage of the electrode and un- lighting of the lamp.

This projector is controlled by an internal microprocessor. Under certain exceptional circumstances, the projector may not operate correctly even for turning off the power. In such a case, please push the restart switch (6) by using a pin or similar. After making sure that the power indicator lights to solid orange, set the power switch to the OFF position. Only push the restart switch in these exceptional instances.

When a power supply is shut off with a power failure or the restart switch, before turning on again, make the projector cool down at least 10 minutes without operating.

20

Downloaded from www.Manualslib.com manuals search engine

Image 22
Contents Manuel dutilisation Guide dutilisation ProjectorUser’s Manual Operating Guide Bedienungsanleitung BenutzerhandbuchDeutsch Bedienungsanleitung Zusätzlicher Français Manuel dutilisation SupplémentaireEspañol Manual de usuario Adicional Thank you for purchasing this projector Trademark acknowledgmentPreparations Power on/offBefore use OperatingMultifunctional settings Easy MenuProjector features About this manualAbout contents of package Part names ProjectorControl buttons Remote controlMagnify Fastening the lens cover About the filter cover bottom-up use When put on a table When suspended from the ceiling ArrangementFor 169 screens For 43 screensAdjusting the projector’s elevator Connecting your devices Examples of connection with a VCR/DVD playerExamples of connection with a computer About Plug-and-Play capability Example of computer signalText Connecting power supply Loading batteries into the remote control Using the remote control Turning on the power STANDBY/ONTurning off the power Adjusting the volume Temporarily muting the soundSelecting an input signal Searching an input signalFor a 43 signal For a 169 signalSelecting an aspect ratio Adjusting the focus Adjusting the zoom magnifying powerUsing the automatic adjustment feature Adjusting the position Correcting the keystone distortionsUsing the partial magnify feature Freezing the screenTemporarily blanking the screen To choose the target menu Using the menu functionTo display a menu EnterSetup Menu To choose the target itemTo return to the previous menu To resetTo operate To close the menuMode DescriptionZoom ColorMirror LanguagePicture menu #1 Default  #1 Custom  #2 Default#3 Custom  #3 Default  #2 Custom GammaCustom  LOW High  MiddleColor Temp SAVE4 SAVE3  SAVE2  SAVE1 TV  Film  Turn OFFLOAD1  LOAD2  LOAD3  LOAD4 MY MemoryFor an RGB signal For a 169 signalFor a 43 signal Image menuPosition SizeFor a video signal or s-video signal Auto Adjust ExecuteFor a component video signal Turn on  Turn OFF Input menuAuto  Ntsc  PAL  Secam Frame LockNormal  Whisper Setup menuNormal  Hinvert  Vinvert  H&VINVERT Menu Position Screen menuBright  Dark Start UP No Input is Detected MessageSync is OUT of Range RGB  S-VIDEO  Video Reset  CancelOption menu Auto OFFEnable  Disable ServiceAuto Adjust FAN SpeedGhost Factory ResetFilter Message Lamp Case of replacement by yourself Type number = DT00707Center point of claws Tabs Usual filter cover Air filterType number = NJ22642 Filter cover for bottom-up usePosition the air filter and filter cover into place Inside of the projector Caring for the cabinet and remote controlCaring for the lens Horizontal or vertical wavelength of the input signal Related messagesPower Regarding the indicator lampsLamp Temp Power Lamp Temp Phenomena that may easily be taken as machine defects If the situation cannot be correctedColor settings are not correctly adjusted Volume is adjusted to an extremely low levelBrightness is adjusted to an extremely low level Color Space setting is not suitableCommunication port SpecificationRGB input Video inputDimension diagram Hitachi Europe GmbH Munich Office Hitachi Home & Life Solutions, Inc. Middle East OfficeDigital Media Div Hitachi Europe S.r.l
Related manuals
Manual 62 pages 37.27 Kb

PJ-LC9 specifications

The Hitachi PJ-LC9 is a compact and versatile projector, renowned for its cutting-edge features and outstanding performance. Ideal for business presentations, educational settings, and home theater use, it blends functionality with user-friendly design. With its impressive specifications, the PJ-LC9 caters to the demands of professionals and casual users alike.

One of the key features of the PJ-LC9 is its native resolution of 1024 x 768 pixels (XGA), which ensures crisp and clear images. This resolution is particularly beneficial for presentations containing detailed graphs, charts, and high-quality images. The projector’s brightness of 2500 ANSI lumens makes it suitable for use in a variety of lighting conditions, allowing it to shine in both dim and well-lit environments.

The PJ-LC9 employs advanced LCD technology, which enhances color accuracy and contrast, providing vibrant and lifelike visuals. This technology aids in delivering sharp and vivid images, which is crucial for capturing and maintaining the audience's attention during presentations or watching media content.

Another standout characteristic of the PJ-LC9 is its lightweight design, weighing just 2.5 kg, which makes it highly portable. Its compact form factor allows users to effortlessly transport it between locations, making it an excellent choice for traveling professionals and educators who need to present on-the-go.

Connectivity options are another advantage of the Hitachi PJ-LC9. It comes equipped with multiple input ports, including HDMI, VGA, and USB, enabling users to connect various devices such as laptops, desktops, and media players without hassle. The inclusion of RS-232C serial connection also makes it compatible with computer control for automation and control purposes.

Additionally, the projector features a built-in 1W speaker, providing adequate sound output for small spaces, although external speakers may still be preferable for larger venues. The PJ-LC9 also supports a range of aspect ratios, including 4:3 and 16:9, allowing for flexibility depending on the content being presented.

In terms of maintenance, the PJ-LC9 utilizes a long-lasting lamp that can deliver up to 3000 hours of operation in standard mode, extending to around 5000 hours in eco mode. This longevity ensures reduced maintenance costs and downtime for users.

In summary, the Hitachi PJ-LC9 is a reliable, feature-rich projector that excels in performance and versatility. Its combination of high resolution, brightness, portability, and connectivity options make it a popular choice for professionals and educators seeking an efficient and effective projection solution.