Poulan 96042001000, 402557 manual Storage, Other, Fuel System, Engine OIL, Cylinders

Page 24

STORAGE

Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more.

WARNING: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure.

TRACTOR

Remove mower from tractor for winter storage. When mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

•Clean entire tractor (See “CLEANING” in the Mainte- nance section of this manual).

•Inspect and replace belts, if necessary (See belt re- placement instructions in the Service and Adjustments section of this manual).

•Lubricate as shown in the Maintenance section of this manual.

•Be sure that all nuts, bolts and screws are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

•Touch up all rusted or chipped paint surfaces; sand lightly before painting.

BATTERY

•Fully charge the battery for storage.

•After a period of time in storage, battery may require recharging.

•To help prevent corrosion and power leakage during long periods of storage, battery cables should be dis- connected and battery cleaned thoroughly (see “TO CLEAN BATTERY AND TERMINALS” in the Mainte- nance section of this manual).

•After cleaning, leave cables disconnected and place cables where they cannot come in contact with battery terminals.

•If battery is removed from tractor for storage, do not store battery directly on concrete or damp surfaces.

ENGINE

FUEL SYSTEM

IMPORTANT: IT IS IMPORTANTTO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTUREWHICH LEADSTO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE.

•Empty the fuel tank by starting the engine and let it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in mini- mizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean en- gine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER(S)

•Remove spark plug(s).

•Pour one ounce of oil through spark plug hole(s) into cylinder(s).

•Turn ignition key to “START” position for a few seconds to distribute oil.

•Replace with new spark plug(s).

OTHER

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your tractor indoors and cover it to give protection from dust and dirt.

•Cover your tractor with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe which allows condensation to form and will cause your tractor to rust.

IMPORTANT: NEVER COVERTRACTOR WHILE ENGINE AND EXHAUST AREAS ARE STILL WARM.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents PB22H48YT Always Wear EYE Protection During OperationSafety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService III. ChildrenIV. Towing Table of Contents Assembly Unassembled PartsTo Remove Tractor from Carton Unpack CartonCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor Reverse Operation System ROS on PositionHOW to USE Your Tractor StoppingTo Adjust Mower Cutting Height See Fig To Adjust Gauge Wheels See FigSystem Characteristics To Operate MowerService REMINDER/HOUR Meter Before Starting the EngineTo Operate on Hills Check Engine OIL LevelTo Start Engine See Fig Purge TransmissionAutomatic Transmission Warm UP Mowing Tips Maintenance MaintenanceGeneral Recommendations ScheduleBattery TractorBrake Operation TiresEngine Service and Adjustments CleaningIN-LINE Fuel Filter See Fig Tractor See FigTo Install Mower See Figs To Level Mower Mower Drive Belt Installation To Replace Mower Blade Drive Belt See FigMower Drive Belt Removal To Replace Motion Drive Belt See Fig To Check BrakeFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTo Start Engine with a Weak Battery See Fig Replacing Battery See FigTo Attach Jumper Cables To Remove CABLES, Reverse OrderTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Engine dies when Limited Warranty Page Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

402557, 96042001000 specifications

The Poulan 402557,96042001000 is a versatile and highly efficient chainsaw designed to handle a variety of cutting tasks. Built with both amateur and professional users in mind, this chainsaw combines power, durability, and user-friendly features to deliver a reliable cutting experience.

At the heart of the Poulan 402557 is a robust engine that provides optimal performance, enabling it to tackle everything from light trimming to heavy-duty tree felling. The chainsaw is equipped with a potent two-stroke engine, which emphasizes efficiency without sacrificing power. With its well-designed air intake and exhaust system, the Poulan 402557 ensures reduced emissions, making it an environmentally friendly choice for users who are conscious about their carbon footprint.

One of the standout features of the Poulan 402557,96042001000 is its lightweight construction, which enhances maneuverability and reduces user fatigue during extended use. Despite its lightweight nature, this chainsaw boasts an impressive cutting capacity, thanks to a sharp and durable chain and bar combination. The chainsaw’s 18-inch bar length makes it suitable for a wide range of cutting applications, providing the perfect balance between control and cutting power.

Safety is a paramount concern in chainsaw design, and Poulan has integrated multiple safety features into the 402557 model. It includes a chain brake system that engages instantly in the event of kickback, providing an additional layer of protection for the operator. Furthermore, the chainsaw comes with an anti-vibration system that minimizes user fatigue and enhances comfort during prolonged use.

Ease of maintenance is another important characteristic of the Poulan 402557. The tool-less chain tensioning system allows users to make quick adjustments without the need for additional tools, ensuring the saw is always optimized for performance. Additionally, the transparent fuel tank window lets users easily monitor fuel levels, preventing unexpected interruptions during work.

In terms of versatility, the Poulan 402557 is compatible with various accessories and attachments, making it suitable for different tasks, such as limbing, bucking, and felling.

In summary, the Poulan 402557,96042001000 chainsaw brings together power, safety features, and user-friendliness, making it an excellent choice for both casual users and professionals alike. Its performance, combined with its innovative technologies, ensures it stands out in a competitive market, promising reliability and efficiency for all cutting needs.
Top Page Image Contents