Poulan 96042001000, 402557 manual Engine dies when

Page 26

TROUBLESHOOTING POINTS

PROBLEM

CAUSE

CORRECTION

 

 

 

 

 

Engine dies when

1.

Reverse operation system

1.

Turn ignition key to

tractor is shifted

 

(ROS) is not "ON" while

 

ROS "ON" position.

into reverse

 

mower or other attachment

 

See Operation section.

 

 

is engaged.

 

 

 

 

 

 

 

Engine continues to run

1.

Faulty operator-safety presence control system.

1.

Check wiring, switches and connections. If not

when operator leaves seat

 

 

 

corrected, contact an authorized service center/

with attachment clutch

 

 

 

department.

engaged

 

 

 

 

 

 

 

 

 

Poor cut - uneven

1.

Worn, bent or loose blade.

1.

Replace blade. Tighten blade bolt.

 

2.

Mower deck not level.

2.

Level mower deck.

 

3.

Buildup of grass, leaves, and trash under mower.

3.

Clean underside of mower housing.

 

4.

Bent blade mandrel.

4.

Replace blade mandrel.

 

5.

Clogged mower deck vent holes from buildup of

5.

Clean around mandrels to open vent holes.

 

 

grass, leaves, and trash around mandrels.

 

 

 

 

 

 

 

Mower blades will not

1.

Obstruction in clutch mechanism.

1.

Remove obstruction.

rotate

2.

Worn/damaged mower drive belt.

2.

Replace mower drive belt.

 

3.

Frozen idler pulley.

3.

Replace idler pulley.

 

4.

Frozen blade mandrel.

4.

Replace blade mandrel.

 

 

 

 

 

Poor grass discharge

1.

Engine speed too slow.

1.

Place throttle control in “FAST” position.

 

2.

Travel speed too fast.

2.

Shift to slower speed.

 

3.

Wet grass.

3.

Allow grass to dry before mowing.

 

4.

Mower deck not level.

4.

Level mower deck.

 

5.

Low/uneven tire air pressure.

5.

Check tires for proper air pressure.

 

6.

Worn, bent or loose blade.

6.

Replace blade. Tighten blade bolt.

 

7.

Buildup of grass, leaves and trash under mower.

7.

Clean underside of mower housing.

 

8.

Mower drive belt worn.

8.

Replace mower drive belt.

 

9.

Blades improperly installed.

9.

Reinstall blades sharp edge down.

 

10.

Improper blades used.

10.

Replace with blades listed in this manual.

 

11.

Clogged mower deck vent holes from buildup of

11.

Clean around mandrels to open vent holes.

 

 

grass, leaves, and trash around mandrels.

 

 

 

 

 

 

 

Headlight(s) not working

1.

Light switch is “OFF”.

1.

Turn light switch “ON”.

(if so equipped)

2.

Bulb(s) or lamp(s) burned out.

2.

Replace bulb(s) or lamp(s).

 

3.

Faulty light switch.

3.

Check/replace light switch.

 

4.

Loose or damaged wiring.

4.

Check wiring and connections.

 

5.

Blown fuse.

5.

Replace fuse.

 

 

 

 

 

Battery will not charge

1.

Bad battery cell(s).

1.

Replace battery.

 

2.

Poor cable connections.

2.

Check/clean all connections.

 

3.

Faulty regulator (if so equipped).

3.

Replace regulator.

 

4.

Faulty alternator.

4.

Replace alternator.

 

 

 

 

 

Loss of drive

1.

Freewheel control in “disengaged” position.

1.

Place freewheel control in “engaged” position.

 

2.

Motion drive belt worn, damaged, or broken.

2.

Replace motion drive belt.

 

3.

Air trapped in transmission during shipment

3.

Purge transmission.

 

 

or servicing.

 

 

 

 

 

 

 

Engine “backfires” when

1.

Engine throttle control not set between half and

1.

Move throttle control between half and full speed

turning engine “OFF”

 

full speed (fast) position before stopping engine.

 

(fast) position before stopping engine.

 

 

 

 

 

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents PB22H48YT Always Wear EYE Protection During OperationGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIV. Towing ServiceIII. Children Table of Contents To Remove Tractor from Carton AssemblyUnassembled Parts Unpack CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor Reverse Operation System ROS on PositionHOW to USE Your Tractor StoppingSystem Characteristics To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerTo Operate on Hills Service REMINDER/HOUR MeterBefore Starting the Engine Check Engine OIL LevelAutomatic Transmission Warm UP To Start Engine See FigPurge Transmission Mowing Tips General Recommendations MaintenanceMaintenance ScheduleBrake Operation BatteryTractor TiresEngine IN-LINE Fuel Filter See Fig Service and AdjustmentsCleaning Tractor See FigTo Install Mower See Figs To Level Mower Mower Drive Belt Removal Mower Drive Belt InstallationTo Replace Mower Blade Drive Belt See Fig Front Wheel TOE-IN/CAMBER To Replace Motion Drive Belt See FigTo Check Brake To Remove Wheel for Repairs See FigTo Attach Jumper Cables To Start Engine with a Weak Battery See FigReplacing Battery See Fig To Remove CABLES, Reverse OrderTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Engine dies when Limited Warranty Page Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

402557, 96042001000 specifications

The Poulan 402557,96042001000 is a versatile and highly efficient chainsaw designed to handle a variety of cutting tasks. Built with both amateur and professional users in mind, this chainsaw combines power, durability, and user-friendly features to deliver a reliable cutting experience.

At the heart of the Poulan 402557 is a robust engine that provides optimal performance, enabling it to tackle everything from light trimming to heavy-duty tree felling. The chainsaw is equipped with a potent two-stroke engine, which emphasizes efficiency without sacrificing power. With its well-designed air intake and exhaust system, the Poulan 402557 ensures reduced emissions, making it an environmentally friendly choice for users who are conscious about their carbon footprint.

One of the standout features of the Poulan 402557,96042001000 is its lightweight construction, which enhances maneuverability and reduces user fatigue during extended use. Despite its lightweight nature, this chainsaw boasts an impressive cutting capacity, thanks to a sharp and durable chain and bar combination. The chainsaw’s 18-inch bar length makes it suitable for a wide range of cutting applications, providing the perfect balance between control and cutting power.

Safety is a paramount concern in chainsaw design, and Poulan has integrated multiple safety features into the 402557 model. It includes a chain brake system that engages instantly in the event of kickback, providing an additional layer of protection for the operator. Furthermore, the chainsaw comes with an anti-vibration system that minimizes user fatigue and enhances comfort during prolonged use.

Ease of maintenance is another important characteristic of the Poulan 402557. The tool-less chain tensioning system allows users to make quick adjustments without the need for additional tools, ensuring the saw is always optimized for performance. Additionally, the transparent fuel tank window lets users easily monitor fuel levels, preventing unexpected interruptions during work.

In terms of versatility, the Poulan 402557 is compatible with various accessories and attachments, making it suitable for different tasks, such as limbing, bucking, and felling.

In summary, the Poulan 402557,96042001000 chainsaw brings together power, safety features, and user-friendliness, making it an excellent choice for both casual users and professionals alike. Its performance, combined with its innovative technologies, ensures it stands out in a competitive market, promising reliability and efficiency for all cutting needs.
Top Page Image Contents