Poulan 96012009000, 424999 manual Transaxle Gear Shift Lever NEUTRAL- Adjustment See Fig

Page 22

SERVICE AND ADJUSTMENTS

TRANSAXLE GEAR SHIFT LEVER NEUTRAL- ADJUSTMENT (See Fig. 21)

The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows:

•Make sure transaxle is in neutral (N).

NOTE: When the tractor rear wheels move freely, the transaxle is in neutral.

•Loosen adjustment bolt in front of the right rear wheel.

•Position the gear shift lever in the neutral (N) posi- tion.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

 

NEUTRAL

GEARSHIFT LEVER

LOCK GATE

 

 

ADJUSTMENT

 

BOLT

FIG. 21

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

RETAINING WASHERS

RING

AXLE

COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 22

TO START ENGINE WITH A WEAK BATTERY (See Fig. 23)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 22)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

22

FIG. 23

Page 21 Page 23
Image 22
Page 21 Page 23
Contents PO18542LT ModelGeneral Operation Safe Operation Practices for Ride-On MowersII. Slope Operation III. Children ServiceIV. Towing Table of Contents Contents of Hardware Pack Before Removing Tractor from Skid Tools Required for AssemblyTo Remove Tractor from Carton Unpack CartonCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills Reverse Operation System ROSTo Operate Mower See Fig To TransportADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips General Recommendations Maintenance ScheduleLubrication Chart Before Each USETo Sharpen Blade See Fig TractorBlade Removal See Fig Important Special blade bolt is heat treatedBelts BatteryEngine Transaxle CoolingAIR Filter CleaningClean AIR Screen MufflerTo Install Mower See Fig To Remove Mower See FigTo Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Check Brake Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbEngine OIL OtherFuel System CylindersTroubleshooting Points Problem Cause CorrectionEngine dies when Canada contact Outdoor Products Customer Service DeptHOP Stevens Creek Road Terry Fox Way Augusta, GA 30907 USAService Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Fold Along This Dotted Line Degree SlopeParts and Service Changere DE Pièces LES ET L’ENTRETIEN Degrés MAX Dentretien Notes Garantie cette de exclus sont normal l’entretien et Dept Service Customer Products Outdoor Canada AuAutorisé Initiale d’achat date la de compter à jours 90 dixDépannage DE Guide Défectueux estRalenti Entreposage MoteurRéglages ET Révision MoteurVitesses DE Boîte LA DE Mentgechan Carrossage AVANT/ Roues DES ConvergenceTionrec -DI LA DE L’ALIGNEMENT Régler Pour DE Levier DU Neutre AU RéglageTransmission DE MENTNETRAÎD’EN Courroie LA Remplacer PourCourroie Acer Rempl Pour Freins LES Vérifier PourDE Boîtier LE Niveau DE Mettre Pour SedeutonTracteur Fig la Voir Tondeuse LA Installer PourReglages ET Revision Tondeuse LA Enlever PourEntretien Lubrification Transmission LA DE RefroidissementBatterie Trapézoïdales CourroiesFig la Voir Lame LA Enlever Fig la Voir Lame LA AffilerEN Fonctionnement DE Système ET Lubrification DE Tableau Recommandations LESGénérales Utilisation Chaque AvantTonte DE Conseils UtilisationUtilisé resoiceslac à et terrain au convient qui vitesse ’ESSENCE Réservoir LE Remplir Moteur LE Démarrer DE AvantMoteur LE Démarrer Pour Moteur DU D’HUILE Niveau LE VérifierTracteur LE Transporter Pour Accessoires AutresET Charrettes DES Remorquer Pour Pentes LES Dans Utiliser PourTeurtrac GAZ DES Commande LA Utiliser PourT O S I L I T U Reculer Pour ET Avancer Pour02829 Moteur Toutes SI Vérifier Toutes SI Vérifier MontageCorrectement Sont Courroies LES NI DE EST Tondeuse LA SI VérifierDesmancom des fonction la et Fig la Voir Batterie LA VérifierPalet LA DE Tracteur LE Retirer Pour Palette LA DU Tracteur LE Sortir PourLE Pour Exigés Outils LES ToncarMontar SIN Piezas Client DU Responsabilités SommaireProduit DE Spécifications Enfants EntretienRemorquage Général EntretienGénéral Fonctionnement PentesLES Dans Fonctionnement Tracteurs des sécurité toute en l’utilisation pour ConseilsAUX Imprimé

424999, 96012009000 specifications

The Poulan 96012009000,424999 is a high-performance chainsaw designed to meet the needs of both professional landscapers and home users. This powerful tool is engineered for efficiency, durability, and ease of use, making it a reliable choice for various cutting tasks, including tree trimming, firewood cutting, and yard maintenance.

One of the standout features of the Poulan 96012009000,424999 is its robust engine. With a potent 42cc two-stroke engine, this chainsaw provides ample power to tackle even the toughest jobs. The engine is designed to produce maximum torque at lower RPMs, which helps to reduce wear while ensuring efficient cutting performance. Its lightweight construction further enhances maneuverability and allows for extended use without causing undue fatigue to the operator.

In addition to its powerful engine, the chainsaw incorporates advanced technologies that promote user comfort and convenience. The ergonomic design features an anti-vibration system that minimizes shock and reduces operator fatigue, allowing for a more enjoyable cutting experience. The wrap-around handle provides improved grip and control, essential for managing the saw during different cutting applications.

Another key characteristic of the Poulan 96012009000,424999 is its easy starting system. The chainsaw is equipped with a simple pull-start mechanism that requires minimal effort, allowing users to get to work quickly without frustration. Additionally, it features an adjustable oiling system, which allows users to control the flow of oil to the chain, ensuring proper lubrication and extending the life of the guide bar and chain.

The 16-inch cutting bar strikes a perfect balance between reach and control, making it versatile enough for a range of cutting tasks. The high-visibility chain saw chain ensures cutting precision, while the built-in chain brake enhances safety by preventing accidental kickback.

Maintenance is made easier with the Poulan 96012009000,424999, as it comes with tool-less chain tensioning, allowing users to quickly and easily adjust the chain tension without the need for additional tools. This feature not only saves time but also ensures optimal performance for every cutting task.

In summary, the Poulan 96012009000,424999 is a powerful, user-friendly chainsaw that combines innovative features and technologies. With its performance-oriented design, ergonomic handling, and features focused on safety and ease of maintenance, this chainsaw stands out as an excellent choice for anyone looking to tackle their cutting needs with confidence and efficiency.
Top Page Image Contents