Poulan 96012009000, 424999 manual Other, Fuel System, Engine OIL, Cylinders

Page 24

STORAGE

Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more.

WARNING: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure.

TRACTOR

Remove mower from tractor for winter storage. When mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

•Clean entire tractor (See “CLEANING” in the Mainte- nance section of this manual).

•Inspect and replace belts, if necessary (See belt re- placement instructions in the Service and Adjustments section of this manual).

•Lubricate as shown in the Maintenance section of this manual.

•Be sure that all nuts, bolts and screws are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

•Touch up all rusted or chipped paint surfaces; sand lightly before painting.

BATTERY

•Fully charge the battery for storage.

•After a period of time in storage, battery may require recharging.

•To help prevent corrosion and power leakage during long periods of storage, battery cables should be dis- connected and battery cleaned thoroughly (see “TO CLEAN BATTERY AND TERMINALS” in the Mainte- nance section of this manual).

•After cleaning, leave cables disconnected and place cables where they cannot come in contact with battery terminals.

•If battery is removed from tractor for storage, do not store battery directly on concrete or damp surfaces.

ENGINE

FUEL SYSTEM

IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE.

•Empty the fuel tank by starting the engine and let it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in mini- mizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean en- gine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER(S)

•Remove spark plug(s).

•Pour one ounce of oil through spark plug hole(s) into cylinder(s).

•Turn ignition key to “START” position for a few seconds to distribute oil.

•Replace with new spark plug(s).

OTHER

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your tractor indoors and cover it to give protection from dust and dirt.

•Cover your tractor with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe which allows condensation to form and will cause your tractor to rust.

IMPORTANT: NEVER COVER TRACTOR WHILE ENGINE AND EXHAUST AREAS ARE STILL WARM.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents PO18542LT ModelSafe Operation Practices for Ride-On Mowers General OperationII. Slope Operation Service III. ChildrenIV. Towing Table of Contents Contents of Hardware Pack Tools Required for Assembly To Remove Tractor from CartonBefore Removing Tractor from Skid Unpack CartonCheck Battery See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS To Operate Mower See FigTo Operate on Hills To TransportBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Maintenance Schedule Lubrication ChartGeneral Recommendations Before Each USETractor Blade Removal See FigTo Sharpen Blade See Fig Important Special blade bolt is heat treatedBattery EngineBelts Transaxle CoolingCleaning Clean AIR ScreenAIR Filter MufflerTo Install Mower See Fig To Remove Mower See FigTo Level Mower Housing FRONT-TO-BACK Adjustment See FigsBelt Installation To Replace Mower Blade Drive Belt See FigTo Check Brake To Replace Motion Drive Belt See FigTransaxle Gear Shift Lever NEUTRAL- Adjustment See Fig To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbOther Fuel SystemEngine OIL CylindersTroubleshooting Points Problem Cause CorrectionEngine dies when Outdoor Products Customer Service Dept HOPCanada contact Stevens Creek Road Terry Fox Way Augusta, GA 30907 USAService Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Fold Along This Dotted Line Degree SlopeParts and Service Changere DE Pièces LES ET L’ENTRETIEN Degrés MAX Dentretien Notes Dept Service Customer Products Outdoor Canada Au AutoriséGarantie cette de exclus sont normal l’entretien et Initiale d’achat date la de compter à jours 90 dixDépannage DE Guide Défectueux estRalenti Entreposage MoteurRéglages ET Révision MoteurCarrossage AVANT/ Roues DES Convergence Tionrec -DI LA DE L’ALIGNEMENT Régler PourVitesses DE Boîte LA DE Mentgechan DE Levier DU Neutre AU RéglageCourroie LA Remplacer Pour Courroie Acer Rempl PourTransmission DE MENTNETRAÎD’EN Freins LES Vérifier PourDE Boîtier LE Niveau DE Mettre Pour SedeutonFig la Voir Tondeuse LA Installer Pour Reglages ET RevisionTracteur Tondeuse LA Enlever PourEntretien Transmission LA DE Refroidissement BatterieLubrification Trapézoïdales CourroiesFig la Voir Lame LA Affiler Fig la Voir Lame LA EnleverEN Fonctionnement DE Système ET Recommandations LES GénéralesLubrification DE Tableau Utilisation Chaque AvantUtilisation Tonte DE ConseilsUtilisé resoiceslac à et terrain au convient qui vitesse Moteur LE Démarrer DE Avant Moteur LE Démarrer Pour’ESSENCE Réservoir LE Remplir Moteur DU D’HUILE Niveau LE VérifierAccessoires Autres ET Charrettes DES Remorquer PourTracteur LE Transporter Pour Pentes LES Dans Utiliser PourGAZ DES Commande LA Utiliser Pour T O S I L I T UTeurtrac Reculer Pour ET Avancer Pour02829 Moteur Montage Correctement Sont Courroies LESToutes SI Vérifier Toutes SI Vérifier NI DE EST Tondeuse LA SI VérifierFig la Voir Batterie LA Vérifier Desmancom des fonction la etPalet LA DE Tracteur LE Retirer Pour DU Tracteur LE Sortir Pour LE Pour Exigés Outils LESPalette LA ToncarMontar SIN Piezas Sommaire Client DU ResponsabilitésProduit DE Spécifications Entretien RemorquageEnfants Général EntretienPentes LES Dans FonctionnementGénéral Fonctionnement Tracteurs des sécurité toute en l’utilisation pour ConseilsAUX Imprimé

424999, 96012009000 specifications

The Poulan 96012009000,424999 is a high-performance chainsaw designed to meet the needs of both professional landscapers and home users. This powerful tool is engineered for efficiency, durability, and ease of use, making it a reliable choice for various cutting tasks, including tree trimming, firewood cutting, and yard maintenance.

One of the standout features of the Poulan 96012009000,424999 is its robust engine. With a potent 42cc two-stroke engine, this chainsaw provides ample power to tackle even the toughest jobs. The engine is designed to produce maximum torque at lower RPMs, which helps to reduce wear while ensuring efficient cutting performance. Its lightweight construction further enhances maneuverability and allows for extended use without causing undue fatigue to the operator.

In addition to its powerful engine, the chainsaw incorporates advanced technologies that promote user comfort and convenience. The ergonomic design features an anti-vibration system that minimizes shock and reduces operator fatigue, allowing for a more enjoyable cutting experience. The wrap-around handle provides improved grip and control, essential for managing the saw during different cutting applications.

Another key characteristic of the Poulan 96012009000,424999 is its easy starting system. The chainsaw is equipped with a simple pull-start mechanism that requires minimal effort, allowing users to get to work quickly without frustration. Additionally, it features an adjustable oiling system, which allows users to control the flow of oil to the chain, ensuring proper lubrication and extending the life of the guide bar and chain.

The 16-inch cutting bar strikes a perfect balance between reach and control, making it versatile enough for a range of cutting tasks. The high-visibility chain saw chain ensures cutting precision, while the built-in chain brake enhances safety by preventing accidental kickback.

Maintenance is made easier with the Poulan 96012009000,424999, as it comes with tool-less chain tensioning, allowing users to quickly and easily adjust the chain tension without the need for additional tools. This feature not only saves time but also ensures optimal performance for every cutting task.

In summary, the Poulan 96012009000,424999 is a powerful, user-friendly chainsaw that combines innovative features and technologies. With its performance-oriented design, ergonomic handling, and features focused on safety and ease of maintenance, this chainsaw stands out as an excellent choice for anyone looking to tackle their cutting needs with confidence and efficiency.
Top Page Image Contents