To Operate Mower, To Operate on Hills, To Transport

•For best cutting performance, grass over 6 inches in height should be mowed twice. Make the ﬁrst cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions. NOTE: Be sure tractor is on a ﬂat level surface.

1.Lower mower and adjust mower to de- sired cutting height(See “TO ADJUST MOWER CUTTING HEIGHT” in this section of manual).

2.Remove retainer spring and clevis pin which secure each gauge wheel bar.

3.Lower gauge wheels to ground. Raise gauge wheels slightly to align holes in bracket and gauge wheel bar and insert clevis pin. Gauge wheels should be slightly off the ground.

4.Replace retainer spring into clevis pin.

5.Be sure all gauge wheels are in the same setting.

IMPORTANT: Be sure to readjust gauge wheels if you change the cutting height of the mower deck.

Retainer spring

01977

Clevis

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equip- ment on rough, rolling terrain or hills.

1.Select desired height of cut.

2.Start mower blades by engaging at- tachment clutch control.

TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deﬂector shield in place.

	Attachment Clutch Lever	Attachemnt
		Lift Lever
	“Engaged” Position
		High Position

Low

Position

“Disengaged” Position

Deﬂector
Shield	0266
	1

TO OPERATE ON HILLS

WARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope. Use the slope guide provided at the back of this manual.

•Choose the slowest speed before start- ing up or down hills.

•Avoid stopping or changing speed on hills.

•If slowing is necessary, move throttle control lever to slower position.

•If stopping is absolutely necessary, push clutch/brake pedal quickly to brake posi- tion and engage parking brake.

•Move motion control lever to neutral (N) position.

IMPORTANT: The motion control lever does not return to neutral (N) position when the clutch/brake pedal is depressed.

•To restart movement, slowly release parking brake and clutch/brake pedal.

•Slowly move motion control lever to slowest setting.

•Make all turns slowly.

TO TRANSPORT

When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Freewheel control is located at the rear drawbar of tractor.

1.Raise attachment lift to highest position with attachment lift control.

2.Pull freewheel control out and down into the slot and release so it is held in the disengaged position.

•Do not push or tow tractor at more than two (2) MPH.

•To re-engage transmission, reverse above procedure.

193282 specifications

The Poulan 193282 is a remarkable chainsaw designed for both amateur and professional users who seek reliability, efficiency, and ease of use. This powerful tool stands out in the market for its combination of features and innovative technologies, making it a popular choice for pruning, cutting firewood, and tackling larger tree jobs.

One of the main features of the Poulan 193282 is its robust 42cc engine, which provides ample power to handle a variety of cutting tasks. This engine is designed with a lightweight construction, allowing for improved maneuverability and reduced fatigue during extended use. The chainsaw's fuel-efficient engine not only cuts down on operational costs but also reduces environmental impact, making it an eco-friendly choice for users concerned about their carbon footprint.

Integration of advanced technologies sets the Poulan 193282 apart from its competitors. It features an automatic oiling system that ensures consistent lubrication of the bar and chain, prolonging the lifespan of the tool and enhancing cutting performance. The chainsaw is equipped with a Smart Start system, which allows for easier pull starts, significantly reducing the effort required to start the engine. This is especially beneficial for novice users who may struggle with traditional starting mechanisms.

The Poulan 193282 also boasts a durable 18-inch cutting bar, which is optimized for both efficiency and precision, making it ideal for a variety of cutting applications. The chainsaw’s chain is designed for quick and tool-less adjustments, allowing users to maintain optimal tension easily and keep it in peak operating condition.

Additionally, the ergonomic design of the Poulan 193282 features a comfortable grip handle, which enhances user control and reduces vibration during operation. This focus on user comfort is further reflected in the chainsaw’s lightweight construction, allowing for greater flexibility and ease of handling, essential for precision cutting.

In terms of safety features, the Poulan 193282 includes a chain brake system that instantly stops the chain in case of kickback, providing an additional layer of protection for the user. The inclusion of a transparent fuel tank facilitates easy monitoring of fuel levels, ensuring that you are never caught off guard during a cutting task.

In summary, the Poulan 193282 is a well-rounded chainsaw that combines power, efficiency, and user-friendly features. Its innovative design and advanced technologies make it an excellent choice for those looking to tackle a wide range of cutting tasks with confidence. Whether you are a seasoned professional or a DIY enthusiast, the Poulan 193282 is equipped to meet your needs, delivering performance that stands the test of time.