To Install Mower, To Level Mower Housing | Poulan 193282 instruction

6.Disconnect front links from deck by removing retainer springs.

7.Raise lift lever to raise suspension arms. Slide mower out from under trac- tor.

IMPORTANT: If an attachment other than the mower deck is to be mounted on the tractor, remove the front links.

TO INSTALL MOWER

1.Raise attachment lift lever to its highest position.

2.Slide mower under tractor with deﬂec- tor shield to right side of tractor.

3.Lower lift lever to its lowest position.

4.Connect front links to mower deck and secure with retainer springs.

5.Connect suspension arms to rear deck brackets and secure with retainer springs.

6.Connect anti-sway bar to chassis bracket and secure with retainer spring.

7.Install belt into electric clutch pulley groove.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inﬂated (See “PROD- UCT SPECIFICATIONS” section of this manual). If tires are over or underinﬂated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjust- ment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 1/8".

• Recheck measurements after adjusting.

Bottom		Bottom edge
edge of		Bottom edge
edge of	00598	of mower to
mower to		of mower to
mower to		ground
ground		ground
ground
A	Ground Line	A
		Suspension Arm
		01553

FRONT-TO-BACK ADJUSTMENT

IMPORTANT: Deck must be level side-to side. If the following front-to-back adjustment is necessary, be sure to adjust both front links equally so mower will stay level side-to-side. To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Check adjustment on right side of trac- tor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjust- ments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2"

lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal num- ber of turns. The two front links must remain equal in length.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

01268

Mandrel

“D” “D”

Both Front Links Should be Equal in Length

01267

Nut “F”	Nut “E”
Nut “F”
Trunnion

Front Links

Lift Link Adjustment Nut

193282 specifications

The Poulan 193282 is a remarkable chainsaw designed for both amateur and professional users who seek reliability, efficiency, and ease of use. This powerful tool stands out in the market for its combination of features and innovative technologies, making it a popular choice for pruning, cutting firewood, and tackling larger tree jobs.

One of the main features of the Poulan 193282 is its robust 42cc engine, which provides ample power to handle a variety of cutting tasks. This engine is designed with a lightweight construction, allowing for improved maneuverability and reduced fatigue during extended use. The chainsaw's fuel-efficient engine not only cuts down on operational costs but also reduces environmental impact, making it an eco-friendly choice for users concerned about their carbon footprint.

Integration of advanced technologies sets the Poulan 193282 apart from its competitors. It features an automatic oiling system that ensures consistent lubrication of the bar and chain, prolonging the lifespan of the tool and enhancing cutting performance. The chainsaw is equipped with a Smart Start system, which allows for easier pull starts, significantly reducing the effort required to start the engine. This is especially beneficial for novice users who may struggle with traditional starting mechanisms.

The Poulan 193282 also boasts a durable 18-inch cutting bar, which is optimized for both efficiency and precision, making it ideal for a variety of cutting applications. The chainsaw’s chain is designed for quick and tool-less adjustments, allowing users to maintain optimal tension easily and keep it in peak operating condition.

Additionally, the ergonomic design of the Poulan 193282 features a comfortable grip handle, which enhances user control and reduces vibration during operation. This focus on user comfort is further reflected in the chainsaw’s lightweight construction, allowing for greater flexibility and ease of handling, essential for precision cutting.

In terms of safety features, the Poulan 193282 includes a chain brake system that instantly stops the chain in case of kickback, providing an additional layer of protection for the user. The inclusion of a transparent fuel tank facilitates easy monitoring of fuel levels, ensuring that you are never caught off guard during a cutting task.

In summary, the Poulan 193282 is a well-rounded chainsaw that combines power, efficiency, and user-friendly features. Its innovative design and advanced technologies make it an excellent choice for those looking to tackle a wide range of cutting tasks with confidence. Whether you are a seasoned professional or a DIY enthusiast, the Poulan 193282 is equipped to meet your needs, delivering performance that stands the test of time.