Poulan 193282 manual Tractor

Page 18

TRACTOR

Always observe safety rules when per- forming any maintenance.

BRAKE OPERATION

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp

objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are working properly. If your trac- tor does not function as described, repair the problem immediately.

•The engine should not start unless the brake pedal is fully depressed and attachement clutch control is in the disengaged position.

•When the engine is running, any at- tempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any at- tempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never op- erate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

BLADE REMOVAL

1.Raise mower to highest position to al- low access to blades.

2.Remove blade bolt, lock washer and flat washer securing blade.

3.Install new or resharpened blade with

trailing edge up towards deck as shown. IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly.

4.Reassemble blade bolt, lock washer and flat washer in exact order as shown.

5.Tighten blade bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: Blade bolt is heat treated. If bolt needs replacing, replace only with approve bolt shown in the Repair Parts.

Flat

Trailing Edge Up

 

 

Mandrel

 

 

2

 

0

14

 

 

Blade

1

 

Assembly

Washer

 

 

 

 

 

 

Lock

 

 

 

 

Washer

 

 

 

 

Blade

 

 

 

Star

 

 

 

 

Bolt

Center Hole

 

 

 

TO SHARPEN BLADE

NOTE: We do not recommend sharp- ening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An unbalanced blade will cause excessive vibration and eventual damage to mower and engine.

•The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone bal- ancer. (When using a cone balancer, follow the instructions supplied with balancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

 

 

Center

5/8" Bolt

01202

Hole

 

or Pin

Blade

 

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. How- ever, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour. NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and termi- nals can cause the battery to “leak” power. 1. Remove terminal guard.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Model NO. CO185H42STC Table of Contents WarrantySafety Rules General OperationII. Slope Operation IV. Service III. ChildrenDo not Safety Rules Product Specifications Customer ResponsibilitiesAPI-SG-SL Unassembled Parts Tools Required for Assembly To Remove Tractor from CartonBefore Removing Tractor from Skid Install Mulcher Plate If previously removed Reposition Right Rear Gauge Wheel ChecklistTo Convert to Bagging or Discharging Check Tire PressureOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower To Operate on HillsTo Transport Towing Carts and Other ATTACH- Ments Before Starting the EngineTo Start Engine Check Engine OIL LevelMowing Tips Mulching Mowing TipsAutomatic Transmission Warm UP Maintenance General RecommendationsBefore Each USE Tractor Engine Service and Adjustments CleaningSIDE-TO-SIDE Adjustment To Install MowerTo Level Mower Housing FRONT-TO-BACK AdjustmentTo Check and Adjust Brake To Replace Mower Blade Drive BeltTo Replace Motion Drive Belt To Start Engine with a Weak Battery Transaxle Motion Control LE- VER Neutral AdjustmentTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor Fuel System BatteryOther Engine OILTroubleshooting Chart Problem Cause CorrectionExcessive Poor grass Suggested Guide for Sighting Slopes for Safe Operation

193282 specifications

The Poulan 193282 is a remarkable chainsaw designed for both amateur and professional users who seek reliability, efficiency, and ease of use. This powerful tool stands out in the market for its combination of features and innovative technologies, making it a popular choice for pruning, cutting firewood, and tackling larger tree jobs.

One of the main features of the Poulan 193282 is its robust 42cc engine, which provides ample power to handle a variety of cutting tasks. This engine is designed with a lightweight construction, allowing for improved maneuverability and reduced fatigue during extended use. The chainsaw's fuel-efficient engine not only cuts down on operational costs but also reduces environmental impact, making it an eco-friendly choice for users concerned about their carbon footprint.

Integration of advanced technologies sets the Poulan 193282 apart from its competitors. It features an automatic oiling system that ensures consistent lubrication of the bar and chain, prolonging the lifespan of the tool and enhancing cutting performance. The chainsaw is equipped with a Smart Start system, which allows for easier pull starts, significantly reducing the effort required to start the engine. This is especially beneficial for novice users who may struggle with traditional starting mechanisms.

The Poulan 193282 also boasts a durable 18-inch cutting bar, which is optimized for both efficiency and precision, making it ideal for a variety of cutting applications. The chainsaw’s chain is designed for quick and tool-less adjustments, allowing users to maintain optimal tension easily and keep it in peak operating condition.

Additionally, the ergonomic design of the Poulan 193282 features a comfortable grip handle, which enhances user control and reduces vibration during operation. This focus on user comfort is further reflected in the chainsaw’s lightweight construction, allowing for greater flexibility and ease of handling, essential for precision cutting.

In terms of safety features, the Poulan 193282 includes a chain brake system that instantly stops the chain in case of kickback, providing an additional layer of protection for the user. The inclusion of a transparent fuel tank facilitates easy monitoring of fuel levels, ensuring that you are never caught off guard during a cutting task.

In summary, the Poulan 193282 is a well-rounded chainsaw that combines power, efficiency, and user-friendly features. Its innovative design and advanced technologies make it an excellent choice for those looking to tackle a wide range of cutting tasks with confidence. Whether you are a seasoned professional or a DIY enthusiast, the Poulan 193282 is equipped to meet your needs, delivering performance that stands the test of time.
Top Page Image Contents