Poulan 192362 manual To Install Mower, To Level Mower Housing, SIDE-TO-SIDE Adjustment

Page 21

6.Disconnect front links from deck by removing retainer springs.

7.Raise lift lever to raise suspension

arms. Slide mower out from under trac- tor.

IMPORTANT: If an attachment other than the mower deck is to be mounted on the tractor, remove the front links.

TO INSTALL MOWER

1.Raise attachment lift lever to its highest position.

2.Slide mower under tractor with deflec- tor shield to right side of tractor.

3.Lower lift lever to its lowest position.

4.Connect front links to mower deck and secure with retainer springs.

5.Connect suspension arms to rear deck brackets and secure with retainer springs.

6.Connect anti-sway bar to chassis bracket and secure with retainer spring.

7.Install belt into electric clutch pulley groove.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PROD- UCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjust- ment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 1/8".

• Recheck measurements after adjusting.

Bottom edge of

Bottom edge of

mower to ground

mower to ground

 

00598

A

Ground Line

A

Suspension Arm

01553

Lift Link Adjustment Nut

FRONT-TO-BACK ADJUSTMENT

IMPORTANT: Deck must be level side-to side. If the following front-to-back adjustment is necessary, be sure to adjust both front links equally so mower will stay level side-to-side. To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Check adjustment on right side of trac- tor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjust- ments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2"

lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal num- ber of turns. The two front links must remain equal in length.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

01268

Mandrel

“D” “D”

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Model NO. CO18542STB Warranty Table of ContentsSafety Rules General OperationII. Slope Operation IV. Service III. ChildrenDo not Safety Rules Product Specifications Customer ResponsibilitiesAPI-SG-SL Unassembled Parts Tools Required for Assembly To Remove Tractor from CartonBefore Removing Tractor from Skid If previously removed Install Mulcher PlateReposition Right Rear Gauge Wheel To Convert to Bagging or DischargingCheck Tire Pressure Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower To Operate on HillsTo Transport To Start Engine Before Starting the EngineTowing Carts and Other ATTACH- Ments Check Engine OIL LevelMowing Tips Maintenance General RecommendationsBefore Each USE Tractor Engine Cleaning Service and AdjustmentsTo Level Mower Housing To Install MowerSIDE-TO-SIDE Adjustment FRONT-TO-BACK AdjustmentTo Check and Adjust Brake To Replace Mower Blade Drive BeltTo Replace Motion Drive Belt Transaxle Gear Shift Lever NEU- Tral Adjustment To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery Front Wheel TOE-IN/CAMBERTo Adjust Carburetor Other BatteryFuel System Engine OILProblem Cause Correction Troubleshooting ChartExcessive Poor grass Suggested Guide for Sighting Slopes for Safe Operation

192362 specifications

The Poulan 192362 is a versatile and durable outdoor power tool designed for homeowners and landscaping professionals alike. Known for its reliability and efficiency, this model stands out in the realm of chain saws, catering to a variety of cutting tasks, from trimming branches to felling trees.

One of the main features of the Poulan 192362 is its powerful engine, typically featuring a 42cc two-stroke engine that provides ample power for demanding jobs while ensuring the tool remains lightweight and manageable. This balance between power and weight makes it particularly appealing to users who require both performance and ease of use.

Equipped with a 16-inch bar and a low-profile chain, the Poulan 192362 facilitates smooth and efficient cutting. The length of the bar is ideal for handling a wide range of cutting applications, making it suitable for residential and light commercial use. The low-profile chain not only enhances cutting performance but also reduces kickback, improving safety during operation.

In terms of technology, the Poulan 192362 is designed with user comfort in mind. It features an ergonomic handle that provides a comfortable grip, reducing fatigue during prolonged use. Additionally, the tool incorporates anti-vibration technology, which further enhances user comfort by minimizing the vibrations transferred from the engine to the user’s hands.

Another notable characteristic of the Poulan 192362 is its easy-start technology. This system allows for quick and easy starting, even in colder conditions, significantly reducing the hassle often associated with starting two-stroke engines. Moreover, the inclusion of an adjustable automatic chain oiler ensures that the chain remains lubricated during operation, thereby extending its life and ensuring optimal performance.

Maintenance and safety are priorities for this model, as evidenced by features like the inertia-activated chain brake, which halts the chain in the event of sudden movements. This safety measure protects the operator from potential accidents, making the Poulan 192362 a smart choice for users concerned about safety during cutting tasks.

Overall, the Poulan 192362 combines power, efficiency, and safety, making it a reliable tool for any outdoor cutting needs. Its blend of features and user-friendly technologies make it an excellent choice for those seeking a robust chain saw that meets both professional and residential demands.
Top Page Image Contents