To Adjust Steering Wheel ALIGN- Ment

BELT INSTALLATION -

1.Carefully work new belt down between transaxle belt keepers and onto the input pulley.

2.Slide belt into the center span keeper.

3.Pull belt toward front of tractor and roll belt around electric clutch and onto engine pulley.

4.Install belt through stationary idler and clutching idler.

5.Reinstall clutch locator and tighten nut securely.

6.Reconnect clutch harness.

7.Make sure belt is in all pulley grooves and inside all belt guides and keepers.

8.Install mower (See “TO INSTALL MOWER” in this section of manual).

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not

horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble with crossbars horizontal. Tighten securely.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS

1.	Block up axle securely.
2.	Remove axle cover, retaining ring and
	washers to allow wheel removal (rear

Electric

Clutch

Clutching

Idler

Stationary Idler

Center Span Keeper

Transaxle Pulley

	Clutch
	Locator
	Clutch
	Wire
01516	Harness

wheels have a square key - Do not lose).

3. Repair tire and reassemble.

NOTE: On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

4.Replace washers and snap retaining ring securely in axle groove.

5.Replace axle cover.

NOTE: To seal tire punctures and prevent ﬂat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

Retaining Washers

TRANSAXLE GEAR SHIFT LEVER NEU- TRAL ADJUSTMENT

The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows:

1.Make sure transaxle is in neutral (N). NOTE: When the tractor rear wheels move freely, the transaxle is in neutral.

2.Loosen adjustment bolt in front of the right rear wheel.

3.Position the gear shift lever in the neu- tral (N) position.

4.Tighten adjustment bolt securely. NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

Gearshift Lever

02239

Neutral

Adjustment Bolt Lock Gate

Ring

Axle
Cover
Square Key	00663
(Rear Wheel Only)

TO START ENGINE WITH A WEAK BATTERY

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, ﬂame and smoking materials away from bat- teries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BAT- TERY" in the MAINTENANCE section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure: IMPORTANT: Your tractor is equipped with a 12 volt system. The other vehicle must also be a 12 volt system. Do not use your tractor battery to start other vehicles.

TO ATTACH JUMPER CABLES -

1.Connect one end of the RED cable to the POSITIVE (+) terminal of each battery(A-B), taking care not to short against tractor chassis.

192362 specifications

The Poulan 192362 is a versatile and durable outdoor power tool designed for homeowners and landscaping professionals alike. Known for its reliability and efficiency, this model stands out in the realm of chain saws, catering to a variety of cutting tasks, from trimming branches to felling trees.

One of the main features of the Poulan 192362 is its powerful engine, typically featuring a 42cc two-stroke engine that provides ample power for demanding jobs while ensuring the tool remains lightweight and manageable. This balance between power and weight makes it particularly appealing to users who require both performance and ease of use.

Equipped with a 16-inch bar and a low-profile chain, the Poulan 192362 facilitates smooth and efficient cutting. The length of the bar is ideal for handling a wide range of cutting applications, making it suitable for residential and light commercial use. The low-profile chain not only enhances cutting performance but also reduces kickback, improving safety during operation.

In terms of technology, the Poulan 192362 is designed with user comfort in mind. It features an ergonomic handle that provides a comfortable grip, reducing fatigue during prolonged use. Additionally, the tool incorporates anti-vibration technology, which further enhances user comfort by minimizing the vibrations transferred from the engine to the user’s hands.

Another notable characteristic of the Poulan 192362 is its easy-start technology. This system allows for quick and easy starting, even in colder conditions, significantly reducing the hassle often associated with starting two-stroke engines. Moreover, the inclusion of an adjustable automatic chain oiler ensures that the chain remains lubricated during operation, thereby extending its life and ensuring optimal performance.

Maintenance and safety are priorities for this model, as evidenced by features like the inertia-activated chain brake, which halts the chain in the event of sudden movements. This safety measure protects the operator from potential accidents, making the Poulan 192362 a smart choice for users concerned about safety during cutting tasks.

Overall, the Poulan 192362 combines power, efficiency, and safety, making it a reliable tool for any outdoor cutting needs. Its blend of features and user-friendly technologies make it an excellent choice for those seeking a robust chain saw that meets both professional and residential demands.