Poulan 402495 manual HOW to USE Your Tractor, Stopping

Page 12

OPERATION

The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask worn over spectacles.

HOW TO USE YOUR TRACTOR

TO SET PARKING BRAKE(See Fig. 14)

Your tractor is equipped with an operator presence sens- ing switch. When engine is running, any attempt by the operator to leave the seat without fi rst setting the parking brake will shut off the engine.

Depress brake pedal (B) all the way down and hold.

Pull parking brake lever (C) up and hold, release pres- sure from brake pedal (B), then release parking brake lever. Pedal should remain in brake position. Make sure parking brake will hold tractor secure.

B

C

FIG. 14

STOPPING

MOWER BLADES

To stop mower blades, push attachment clutch switch in to disengaged position (o).

(-) ATTACHMENT

(o) PUSH-IN TO

CLUTCH SWITCH

“DISENGAGED”

PULL OUT TO “ENGAGE”

 

FIG. 15

GROUND DRIVE -

To stop ground drive, depress brake pedal all the way down.

ENGINE -

Move throttle control (D) between half and full speed (fast) position.

NOTE: Failure to move throttle control between half and full speed (fast) position, before stopping, may cause en- gine to “backfi re”.

Turn ignition key (F) to “STOP” position and remove key. Always remove key when leaving tractor to prevent unauthorized use.

Never use choke (N) to stop engine.

IMPORTANT: Leaving the ignition switch in any position other than "STOP" will cause the battery to discharge and go dead.

NOTE: Under certain conditions when tractor is standing idle with the engine running, hot engine exhaust gases may cause “browning” of grass. To eliminate this possibility, al- ways stop engine when stopping tractor on grass areas.

CAUTION: Always stop tractor com- pletely, as described above, before leaving the operator's position.

D

N

F

FIG. 16

TO USE THROTTLE CONTROL (See Fig. 16)

Always operate engine at full speed (fast).

Operating engine at less than full speed (fast) reduces engines operating effi ciency.

Full speed (fast) offers the best bagging and mower performance.

TO USE CHOKE CONTROL -D (See Fig. 16)

Use choke control whenever you are starting a cold engine. Do not use to start a warm engine.

To engage choke control, pull knob out. Slowly push knob in to disengage.

TO MOVE FORWARD AND BACKWARD -N (See Fig. 17)

The direction and speed of movement is controlled by the forward and reverse drive pedals.

Start tractor and release parking brake.

Slowly depress forward (K) or reverse (L) drive pedal to begin movement. Ground speed increases the further down the pedal is depressed.

12

Image 12
Contents PBGT22H54 Always Wear EYE Protection During OperationSafety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService III. ChildrenIV. Towing Table of Contents Unassembled Parts Mower Mower Front WheelSlope Sheet KeysAssembly Tools Required for AssemblyTo Remove Tractor from Carton Unpack CartonInstall Mower and Drive Belt First Install ANTI-SWAY BAR S7/16 Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor Reverse Operation System ROS on PositionHOW to USE Your Tractor StoppingTo Adjust Mower Cutting Height See Fig To Adjust Gauge Wheels See FigSystem Characteristics To USE Cruise Control -J See FigService REMINDER/HOUR Meter Using the Reverse Operation SystemReverse Operation System ROS To Operate on HillsBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Maintenance Lubrication ChartBattery TractorBrake Operation TiresEngine Cleaning Engine OIL FilterMuffler Spark PlugsService and Adjustments To Install MowerTractor See Fig To Remove MowerTurn nut right Turn nut left To raise mower To Replace Mower Blade Drive Belt To Check BrakeTo Replace Motion Drive Belt To Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Remove Wheel for Repairs See Fig To Attach Jumper CablesTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Engine dies when Page Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

402495 specifications

The Poulan 402495 is a versatile and efficient chainsaw designed for both casual users and seasoned professionals. Known for its reliability and ease of operation, this model stands out in the competitive market of outdoor power equipment.

One of the main features of the Poulan 402495 is its powerful 40cc two-stroke engine. This engine provides ample power for a range of tasks, from light trimming to more intensive cutting. The engine is designed to deliver a robust performance while maintaining fuel efficiency, making it an economical choice for users who require consistent usage over time.

In addition to its powerful engine, the Poulan 402495 incorporates the revolutionary OxyPower technology. This innovative technology is engineered to increase engine efficiency by optimizing the combustion process. As a result, users can expect reduced emissions and improved fuel economy, which aligns with the growing demand for environmentally friendly power tools.

Another notable feature is its lightweight design, which contributes to excellent maneuverability and ease of handling. The chainsaw weighs in at a manageable level, allowing users to work for extended periods without experiencing excessive fatigue. This is particularly advantageous for professionals and homeowners who have larger cutting jobs ahead of them.

Safety is also a priority in the design of the Poulan 402495. It comes equipped with a chain brake that instantly stops the chain in the event of kickback, providing an additional layer of protection. The model also incorporates a low vibration system that minimizes operator fatigue and enhances comfort during prolonged use.

Moreover, the Poulan 402495 features an automatic oiling system that ensures the chain remains lubricated during use. This not only prolongs the life of the chain but also ensures smooth operation and minimal wear. The tool-less chain tensioning mechanism allows for quick adjustments, making it convenient for users to maintain optimal chain performance without needing extra tools.

In summary, the Poulan 402495 is an excellent choice for those seeking a reliable, efficient, and user-friendly chainsaw. With its powerful engine, advanced OxyPower technology, safety features, and ease of maintenance, it is a formidable tool for a variety of cutting tasks, making it a favorite among homeowners and professionals alike.