Poulan 402495 To Adjust Throttle Control Cable, To Replace Headlight Bulb, Interlocks and Relays

Page 25

SERVICE AND ADJUSTMENTS

REPLACING BATTERY (See Fig. 36)

WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected fi rst to prevent spark- ing from accidental grounding.

•Lift hood to raised position.

•Disconnect BLACK battery cable (A) then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•First connect RED battery cable (B) to positive (+) battery terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover (C) over terminal.

•Connect BLACK grounding cable to negative (-) battery terminal with remaining hex bolt and keps nut. Tighten securely

•Close hood.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 37)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT

WIRE

CONNECTOR

02141

C

Positive B (Red) Cable

ANegative (Black) Cable

FIG. 37

ENGINE

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is nec- essary, see engine manual.

02954

FIG. 36

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO ADJUST CHOKE CONTROL

The choke control has been preset at the factory and ad- justment should not be necessary. If adjustment is neces- sary, see engne manual.

TO ADJUST CARBURETOR

Your carburetor is not adjustable. If your engine does not operate properly due to suspected carburetor problems, take your tractor to an authorized service center for repair and/or adjustment.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Always Wear EYE Protection During Operation PBGT22H54Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationIII. Children ServiceIV. Towing Table of Contents Mower Mower Front Wheel Unassembled PartsSlope Sheet KeysTools Required for Assembly AssemblyTo Remove Tractor from Carton Unpack CartonFirst Install ANTI-SWAY BAR S Install Mower and Drive Belt7/16 Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Reverse Operation System ROS on Position Know Your TractorStopping HOW to USE Your TractorTo Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigSystem Characteristics To USE Cruise Control -J See FigUsing the Reverse Operation System Service REMINDER/HOUR MeterReverse Operation System ROS To Operate on HillsCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigMowing Tips Lubrication Chart MaintenanceTractor BatteryBrake Operation TiresEngine Engine OIL Filter CleaningMuffler Spark PlugsTo Install Mower Service and AdjustmentsTractor See Fig To Remove MowerTurn nut right Turn nut left To raise mower To Check Brake To Replace Mower Blade Drive BeltTo Replace Motion Drive Belt Front Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigTo Remove Wheel for Repairs See Fig To Attach Jumper CablesTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILTroubleshooting Points Engine dies when Page Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

402495 specifications

The Poulan 402495 is a versatile and efficient chainsaw designed for both casual users and seasoned professionals. Known for its reliability and ease of operation, this model stands out in the competitive market of outdoor power equipment.

One of the main features of the Poulan 402495 is its powerful 40cc two-stroke engine. This engine provides ample power for a range of tasks, from light trimming to more intensive cutting. The engine is designed to deliver a robust performance while maintaining fuel efficiency, making it an economical choice for users who require consistent usage over time.

In addition to its powerful engine, the Poulan 402495 incorporates the revolutionary OxyPower technology. This innovative technology is engineered to increase engine efficiency by optimizing the combustion process. As a result, users can expect reduced emissions and improved fuel economy, which aligns with the growing demand for environmentally friendly power tools.

Another notable feature is its lightweight design, which contributes to excellent maneuverability and ease of handling. The chainsaw weighs in at a manageable level, allowing users to work for extended periods without experiencing excessive fatigue. This is particularly advantageous for professionals and homeowners who have larger cutting jobs ahead of them.

Safety is also a priority in the design of the Poulan 402495. It comes equipped with a chain brake that instantly stops the chain in the event of kickback, providing an additional layer of protection. The model also incorporates a low vibration system that minimizes operator fatigue and enhances comfort during prolonged use.

Moreover, the Poulan 402495 features an automatic oiling system that ensures the chain remains lubricated during use. This not only prolongs the life of the chain but also ensures smooth operation and minimal wear. The tool-less chain tensioning mechanism allows for quick adjustments, making it convenient for users to maintain optimal chain performance without needing extra tools.

In summary, the Poulan 402495 is an excellent choice for those seeking a reliable, efficient, and user-friendly chainsaw. With its powerful engine, advanced OxyPower technology, safety features, and ease of maintenance, it is a formidable tool for a variety of cutting tasks, making it a favorite among homeowners and professionals alike.
Top Page Image Contents