Poulan 190288 manual HOW to SET UP Your Tractor, Install Seat See Fig, Check Battery See Fig

Page 7

ASSEMBLY

HOW TO SET UP YOUR TRACTOR

INSTALL SEAT (See Fig. 2)

Adjust seat before tightening adjustment bolt.

•Remove adjustment bolt, lock washer and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjust- ment bolt, lockwasher and flat washer loosely. Do not tighten

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment bolt securely.

SEAT

SEAT PAN

SHOULDER

BOLT

02466

FLAT WASHER

LOCK WASHER

02465

ADJUSTMENT

BOLT

FIG. 2

CHECK BATTERY (See Fig. 3)

•Lift seat pan to raised position.

•If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in MAINTENANCE section of this manual for charging instructions).

SEAT PAN

LABEL

FIG. 3

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

TO ROLL TRACTOR OFF SKID (See Op- eration section for location and function of controls)

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Release parking brake by depressing clutch/brake pedal.

•Place freewheel control in "transmission disengaged position" (See “TO TRANSPORT” in the Operation section of this manual).

•Roll tractor forward off skid.

•Remove banding holding the deflector shield up against tractor.

TO DRIVE TRACTOR OFF SKID (See Op- eration section for location and function of controls)

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

•Be sure all the above assembly steps have been com- pleted.

•Check engine oil level and fill fuel tank with gasoline.

•Place freewheel control in "transmission engaged" position (see "TO TRANSPORT" in Operation section of this manual).

•Sit on seat in operating position, depress clutch/brake pedal and set the parking brake.

•Place motion control lever in neutral (N) position.

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Start the engine.After engine has started, move throttle control to idle position.

•Release parking brake.

•Slowly move the motion control lever forward and slowly drive tractor off skid.

•Apply brake to stop tractor, set parking brake and place motion control lever in neutral position.

•Turn ignition key to "STOP" position.

Continue with the instructions that follow.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Model NO. PO175H42STA Safety Rules Safety Rules Table of Contents Slope Sheet Unassembled PartsSteering Wheel Seat KeyBefore Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig HOW to SET UP Your TractorCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills Before Starting the EngineTo Operate Mower See Fig To Transport See FigsAutomatic Transmission Warm UP ADD GasolineTo Start Engine See Fig Purge TransmissionMowing Tips Before Each USE MaintenanceLubrication Chart General RecommendationsTractor Engine Spark Plugs CleaningAIR Filter MufflerTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig Belt InstallationBelt Removal To Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTransaxle Motion Control Lever Neutral Adjustment See Fig To Adjust BrakeTo Adjust Steering Wheel Alignment Transmission REMOVAL/REPLACEMENTFront Wheel TOE-IN/CAMBER To Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsWith attachment clutch Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

190288 specifications

The Poulan 190288 is a powerful and versatile chainsaw that is designed for both professional landscapers and home users. Renowned for its robustness and reliability, this model exemplifies the perfect balance of performance and ease of use.

One of the standout features of the Poulan 190288 is its 18-inch cutting bar, which provides users with a generous reach, allowing for efficient cutting of medium to large trees and branches. This longer reach translates to reduced time spent on the job, making it an excellent choice for both forestry tasks and property maintenance.

At the heart of the Poulan 190288 is a dependable 42cc engine that delivers remarkable power and torque. This engine is designed to handle tough jobs with ease, whether it's felling trees, limbing, or trimming. The engine also employs advanced technologies that enhance fuel efficiency and reduce emissions, fulfilling environmental standards while delivering excellent performance.

The chainsaw features an automatic oiling system, which ensures that the chain is always lubricated without the need for constant manual adjustment. This not only extends the life of the bar and chain but also allows users to focus on their tasks rather than worrying about maintenance. Additionally, the tool-less chain tensioning system is a significant advantage; it allows for quick adjustments to the chain tension, promoting safety and efficiency during operation.

User comfort is a major consideration in the design of the Poulan 190288. It includes features such as an anti-vibration system, which minimizes fatigue during extended use. The ergonomic handle design ensures a comfortable grip, enhancing overall control and maneuverability.

Maintenance is straightforward thanks to the easy-access air filter and spark plug, making routine upkeep manageable even for those who are less mechanically inclined. The Poulan 190288 is also built to last, with high-quality materials that can withstand harsh working conditions.

In summary, the Poulan 190288 is a well-rounded chainsaw that combines power, efficiency, and user-friendly features. Whether you need it for residential tasks or professional landscaping, this chainsaw is designed to meet a variety of cutting demands while ensuring safety and comfort through innovative design. With its thoughtful engineering and robust construction, the Poulan 190288 stands out as a reliable tool in any woodworker's or landscaper's arsenal.
Top Page Image Contents