Poulan 190288 manual To Replace Mower Blade Drive Belt See Fig, Belt Removal, Belt Installation

Page 20

SERVICE AND ADJUSTMENTS

SIDE-TO-SIDE ADJUSTMENT (See Figs. 15 and 16)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Three full turns of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE

 

BOTTOM EDGE

OF MOWER

 

OF MOWER

TO GROUND

 

TO GROUND

“A”

GROUND LINE

“A”

FIG. 15

SUSPENSION ARM

LIFT LINK ADJUSTMENT NUT

FIG. 16

FRONT-TO-BACK ADJUSTMENT (See Figs. 17 and 18)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its high- est position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns. The two front links must remain equal in length.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

MANDREL

"D"

"D"

FIG. 17

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT "F"

NUT "E"

TRUNNION

FRONT LINKS

FIG. 18

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 19)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Remove mower from tractor (See “TO REMOVE MOWER” in this section of this manual).

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Install new belt in reverse order of removal.

•Make sure belt is in all pulley grooves and inside all belt guides.

•Install mower in reverse order of removal instructions.

IDLER PULLEYS

MANDREL PULLEYS

FIG. 19

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Model NO. PO175H42STA Safety Rules Safety Rules Table of Contents Unassembled Parts Steering Wheel SeatKey Slope SheetAssembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig HOW to SET UP Your TractorInstall Seat See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine To Operate Mower See FigTo Transport See Figs To Operate on HillsADD Gasoline To Start Engine See FigPurge Transmission Automatic Transmission Warm UPMowing Tips Maintenance Lubrication ChartGeneral Recommendations Before Each USETractor Engine Cleaning AIR FilterMuffler Spark PlugsService and Adjustments To Install Mower See FigTo Level Mower Housing To Remove Mower See FigBelt Removal Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Check and Adjust Brake See Fig Transaxle Motion Control Lever Neutral Adjustment See FigTo Adjust Brake To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel Alignment To Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionWith attachment clutch Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX

190288 specifications

The Poulan 190288 is a powerful and versatile chainsaw that is designed for both professional landscapers and home users. Renowned for its robustness and reliability, this model exemplifies the perfect balance of performance and ease of use.

One of the standout features of the Poulan 190288 is its 18-inch cutting bar, which provides users with a generous reach, allowing for efficient cutting of medium to large trees and branches. This longer reach translates to reduced time spent on the job, making it an excellent choice for both forestry tasks and property maintenance.

At the heart of the Poulan 190288 is a dependable 42cc engine that delivers remarkable power and torque. This engine is designed to handle tough jobs with ease, whether it's felling trees, limbing, or trimming. The engine also employs advanced technologies that enhance fuel efficiency and reduce emissions, fulfilling environmental standards while delivering excellent performance.

The chainsaw features an automatic oiling system, which ensures that the chain is always lubricated without the need for constant manual adjustment. This not only extends the life of the bar and chain but also allows users to focus on their tasks rather than worrying about maintenance. Additionally, the tool-less chain tensioning system is a significant advantage; it allows for quick adjustments to the chain tension, promoting safety and efficiency during operation.

User comfort is a major consideration in the design of the Poulan 190288. It includes features such as an anti-vibration system, which minimizes fatigue during extended use. The ergonomic handle design ensures a comfortable grip, enhancing overall control and maneuverability.

Maintenance is straightforward thanks to the easy-access air filter and spark plug, making routine upkeep manageable even for those who are less mechanically inclined. The Poulan 190288 is also built to last, with high-quality materials that can withstand harsh working conditions.

In summary, the Poulan 190288 is a well-rounded chainsaw that combines power, efficiency, and user-friendly features. Whether you need it for residential tasks or professional landscaping, this chainsaw is designed to meet a variety of cutting demands while ensuring safety and comfort through innovative design. With its thoughtful engineering and robust construction, the Poulan 190288 stands out as a reliable tool in any woodworker's or landscaper's arsenal.
Top Page Image Contents