Poulan 190288 manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

Page 23

SERVICE AND ADJUSTMENTS

•Lift seat pan to raised position.

•Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal.

•Connect BLACK grounding cable to negative (-) ter- minal with remaining hex bolt and keps nut. Tighten securely.

SEAT PAN

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 27)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT

WIRE

CONNECTOR

01536

 

FIG. 25

TERMINAL

KEPS NUT

HEX

COVER

 

BOLT

POSITIVE (RED) CABLE

NEGATIVE (BLACK) CABLE

FIG. 26

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

FIG. 27

ENGINE

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is nec- essary, see engine manual.

TO ADJUST CHOKE CONTROL

The choke control has been preset at the factory and ad- justment should not be necessary. If adjustment is neces- sary, see engne manual.

TO ADJUST CARBURETOR

Your carburetor is not adjustable. If your engine does not operate properly due to suspected carburetor problems, take your tractor to an authorized service center for repair and/or adjustment.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Model NO. PO175H42STA Safety Rules Safety Rules Table of Contents Slope Sheet Unassembled PartsSteering Wheel Seat KeyBefore Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonCheck Battery See Fig HOW to SET UP Your TractorInstall Seat See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills Before Starting the EngineTo Operate Mower See Fig To Transport See FigsAutomatic Transmission Warm UP ADD GasolineTo Start Engine See Fig Purge TransmissionMowing Tips Before Each USE MaintenanceLubrication Chart General RecommendationsTractor Engine Spark Plugs CleaningAIR Filter MufflerTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower HousingBelt Removal Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTransaxle Motion Control Lever Neutral Adjustment See Fig To Adjust BrakeFront Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel Alignment To Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsWith attachment clutch Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

190288 specifications

The Poulan 190288 is a powerful and versatile chainsaw that is designed for both professional landscapers and home users. Renowned for its robustness and reliability, this model exemplifies the perfect balance of performance and ease of use.

One of the standout features of the Poulan 190288 is its 18-inch cutting bar, which provides users with a generous reach, allowing for efficient cutting of medium to large trees and branches. This longer reach translates to reduced time spent on the job, making it an excellent choice for both forestry tasks and property maintenance.

At the heart of the Poulan 190288 is a dependable 42cc engine that delivers remarkable power and torque. This engine is designed to handle tough jobs with ease, whether it's felling trees, limbing, or trimming. The engine also employs advanced technologies that enhance fuel efficiency and reduce emissions, fulfilling environmental standards while delivering excellent performance.

The chainsaw features an automatic oiling system, which ensures that the chain is always lubricated without the need for constant manual adjustment. This not only extends the life of the bar and chain but also allows users to focus on their tasks rather than worrying about maintenance. Additionally, the tool-less chain tensioning system is a significant advantage; it allows for quick adjustments to the chain tension, promoting safety and efficiency during operation.

User comfort is a major consideration in the design of the Poulan 190288. It includes features such as an anti-vibration system, which minimizes fatigue during extended use. The ergonomic handle design ensures a comfortable grip, enhancing overall control and maneuverability.

Maintenance is straightforward thanks to the easy-access air filter and spark plug, making routine upkeep manageable even for those who are less mechanically inclined. The Poulan 190288 is also built to last, with high-quality materials that can withstand harsh working conditions.

In summary, the Poulan 190288 is a well-rounded chainsaw that combines power, efficiency, and user-friendly features. Whether you need it for residential tasks or professional landscaping, this chainsaw is designed to meet a variety of cutting demands while ensuring safety and comfort through innovative design. With its thoughtful engineering and robust construction, the Poulan 190288 stands out as a reliable tool in any woodworker's or landscaper's arsenal.
Top Page Image Contents