Poulan 188695 manual Tractor, Brake Operation, Tires, Operator Presence System, Blade Care

Page 15

MAINTENANCE

TRACTOR

Always observe safety rules when performing any main- tenance.

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are work- ing properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the clutch/brake pedal is fully depressed and attachement clutch control is in the disengaged position.

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

BLADE REMOVAL (See Fig. 8)

•Raise mower to highest position to allow access to blades.

•Remove blade bolt, lock washer and flat washer securing blade.

•Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Reassemble blade bolt, lock washer and flat washer in exact order as shown.

•Tighten blade bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: BLADE BOLT IS HEATTREATED.IF BOLT NEEDS REPLACING, REPLACE ONLY WITH APPROVE BOLT SHOWN IN THE REPAIR PARTS.

MANDREL

TRAILINGASSEMBLY EDGE UP

CENTER

HOLE

LOCK WASHER

STAR

FLAT WASHER

BLADE

 

BLADE BOLT

FIG. 8

TO SHARPEN BLADE (See Fig. 9)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An un- balanced blade will cause excessive vibration and eventual damage to mower and engine.

•The blade can be sharpened with a file or on a grind- ing wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

CENTER HOLE

5/8" BOLT

BLADE

OR PIN

 

FIG. 9

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Model NO. PO15538A II. Slope Operation Safety RulesIV. Service General OperationSafety Rules Table of Contents Steering Wheel Seat Unassembled PartsBefore Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonHOW to SET UP Your Tractor Install Seat See FigCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine To Start Engine See Fig Mowing TipsBefore Each USE MaintenanceLubrication Chart General RecommendationsOperator Presence System TractorBrake Operation TiresTransaxle Cooling BatteryEngine BeltsMuffler CleaningClean AIR Screen AIR FilterService and Adjustments To Install Mower See FigTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig To Check and Adjust Brake See FigFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigTo Adjust Steering Wheel ALIGN- Ment To Replace Motion Drive Belt See FigTo Replace Fuse Replacing Battery See FigsTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Carburetor To Remove Hood and Grill Assembly See FigTo Adjust Throttle Control Cable To Adjust Choke ControlEngine OIL StorageOther Fuel SystemTroubleshooting Points With attachment clutch Tractor - Model Number PO15538A SchematicElectrical KEY Part Description Chassis Repair Parts Drive KEY Part NO. NO. Description Steering KEY Part Description Spark Arrester Engine Optional Equipment1712 SeatWheels & Tires DecalsMower Lift Mower Deck Repair Parts Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

188695 specifications

The Poulan 188695 is a powerful and reliable chainsaw designed to meet the demanding needs of both professionals and homeowners. Known for its robust performance and user-friendly features, this model stands out in the competitive chainsaw market.

One of the main features of the Poulan 188695 is its powerful engine. It is equipped with a high-performance 50cc two-stroke engine that provides ample power for tackling various cutting tasks. Whether you're felling trees, pruning branches, or cutting firewood, the Poulan 188695 can handle it all with ease. The engine is also designed for efficient fuel consumption, making it economical for extended use.

Another significant characteristic of the Poulan 188695 is its lightweight design. Weighing in at just around 12 pounds, this chainsaw is easy to maneuver, reducing operator fatigue during long cutting sessions. The balanced design also enhances control and stability, allowing for precise cuts, even in challenging positions.

The Poulan 188695 features a 18-inch bar and chain, which strikes a perfect balance between reach and control. This length is ideal for tackling medium-sized trees and allows for versatility in various cutting applications. The bar and chain are designed for durability, ensuring that users can rely on them for repeated use without experiencing excessive wear.

In terms of technology, the Poulan 188695 incorporates an automated oiler system that keeps the chain adequately lubricated during operation. This system helps to extend the life of the chain and bar, reducing maintenance needs and downtime. Additionally, the chainsaw features an easy-access air filter, allowing for quick cleaning and replacement, which is essential for maintaining optimal performance.

Safety is also a priority in the design of the Poulan 188695. It comes equipped with safety features such as a chain brake and low-vibration technology, which help to minimize the risk of accidents and enhance user comfort. The ergonomic handle design also provides a secure grip, further promoting safe operation.

Overall, the Poulan 188695 is an excellent choice for those seeking a reliable and efficient chainsaw. With its powerful engine, lightweight design, and user-friendly features, it is well-suited for a variety of cutting tasks, making it a valuable addition to any toolbox. Whether you are a seasoned professional or a weekend warrior, the Poulan 188695 is designed to deliver performance and reliability.
Top Page Image Contents