Poulan 188695 manual To Level Mower Housing, FRONT-TO-BACK Adjustment See Figs

Page 19

SERVICE AND ADJUSTMENTS

•Push clutch cable housing guide into bracket, slide col- lar onto guide and secure with large retainer spring.

•Place flat washer and clutch spring on idler pulley bolt and secure with small retainer spring.

•Install belt onto engine pulley.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PRODUCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 14 and 15)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Three full turns of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE OF

 

BOTTOM EDGE

MOWER

00598

OF MOWER

TO GROUND

 

TO GROUND

“A”“A”

GROUND LINE

FIG. 14

SUSPENSION ARM

01553

LIFT LINK

ADJUSTMENT

NUT

FIG. 15

FRONT-TO-BACK ADJUSTMENT (See Figs. 16 and 17)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its high- est position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns. The two front links must remain equal in length.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

MANDREL

01268

"D"

"D"

FIG. 16

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

01267

NUT "F"

NUT "E"

TRUNNION

FRONT LINKS

FIG. 17

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Model NO. PO15538A II. Slope Operation Safety RulesIV. Service General OperationSafety Rules Table of Contents Steering Wheel Seat Unassembled PartsBefore Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig HOW to SET UP Your TractorCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine To Start Engine See Fig Mowing TipsBefore Each USE MaintenanceLubrication Chart General RecommendationsOperator Presence System TractorBrake Operation TiresTransaxle Cooling BatteryEngine BeltsMuffler CleaningClean AIR Screen AIR FilterTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig To Check and Adjust Brake See FigFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigTo Adjust Steering Wheel ALIGN- Ment To Replace Motion Drive Belt See FigTo Replace Fuse Replacing Battery See FigsTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Carburetor To Remove Hood and Grill Assembly See FigTo Adjust Throttle Control Cable To Adjust Choke ControlEngine OIL StorageOther Fuel SystemTroubleshooting Points With attachment clutch Tractor - Model Number PO15538A SchematicElectrical KEY Part Description Chassis Repair Parts Drive KEY Part NO. NO. Description Steering KEY Part Description Spark Arrester Engine Optional Equipment1712 SeatWheels & Tires DecalsMower Lift Mower Deck Repair Parts Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

188695 specifications

The Poulan 188695 is a powerful and reliable chainsaw designed to meet the demanding needs of both professionals and homeowners. Known for its robust performance and user-friendly features, this model stands out in the competitive chainsaw market.

One of the main features of the Poulan 188695 is its powerful engine. It is equipped with a high-performance 50cc two-stroke engine that provides ample power for tackling various cutting tasks. Whether you're felling trees, pruning branches, or cutting firewood, the Poulan 188695 can handle it all with ease. The engine is also designed for efficient fuel consumption, making it economical for extended use.

Another significant characteristic of the Poulan 188695 is its lightweight design. Weighing in at just around 12 pounds, this chainsaw is easy to maneuver, reducing operator fatigue during long cutting sessions. The balanced design also enhances control and stability, allowing for precise cuts, even in challenging positions.

The Poulan 188695 features a 18-inch bar and chain, which strikes a perfect balance between reach and control. This length is ideal for tackling medium-sized trees and allows for versatility in various cutting applications. The bar and chain are designed for durability, ensuring that users can rely on them for repeated use without experiencing excessive wear.

In terms of technology, the Poulan 188695 incorporates an automated oiler system that keeps the chain adequately lubricated during operation. This system helps to extend the life of the chain and bar, reducing maintenance needs and downtime. Additionally, the chainsaw features an easy-access air filter, allowing for quick cleaning and replacement, which is essential for maintaining optimal performance.

Safety is also a priority in the design of the Poulan 188695. It comes equipped with safety features such as a chain brake and low-vibration technology, which help to minimize the risk of accidents and enhance user comfort. The ergonomic handle design also provides a secure grip, further promoting safe operation.

Overall, the Poulan 188695 is an excellent choice for those seeking a reliable and efficient chainsaw. With its powerful engine, lightweight design, and user-friendly features, it is well-suited for a variety of cutting tasks, making it a valuable addition to any toolbox. Whether you are a seasoned professional or a weekend warrior, the Poulan 188695 is designed to deliver performance and reliability.
Top Page Image Contents