SERVICE AND ADJUSTMENTS
TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 33)
The motion control lever has been preset at the factory and adjustment should not be necessary.
•Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.
•Start engine and move motion control lever until tractor does not move forward or backward.
•Hold motion control lever in that position and turn engine off.
•While holding motion control lever in place, loosen the adjustment bolt.
•Move motion control lever to the neutral (lock gate) position.
•Tighten adjustment bolt securely.
NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.
After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:
•Loosen the adjustment bolt.
•Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.
•Tighten adjustment bolt securely.
•Start engine and test.
•If tractor still creeps, repeat above steps until satisfied.
RETAINING WASHERS
RING
AXLE
COVER
SQUARE KEY
(REAR WHEEL ONLY) 
Fig. 34
•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.
•Replace washers and snap retaining ring securely in axle groove.
•Replace axle cover.
NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.
TO START ENGINE WITH A WEAK BATTERY (See Fig. 35)
WARNING:
MOTION CONTROL LEVER | NEUTRAL |
| LOCK GATE |
| ADJUSTMENT |
| BOLT |
Fig. 33
TO ADJUST STEERING WHEEL ALIGNMENT
If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.
FRONT WHEEL TOE-IN/CAMBER
The front wheel
TO REMOVE WHEEL FOR REPAIRS (See Fig. 34)
•Block up axle securely.
•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).
•Repair tire and reassemble.
22
If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).
If “jumper cables” are used for emergency starting, follow this procedure:
IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.
TO ATTACH JUMPER CABLES -
•Connect one end of the RED cable to the POSITIVE
(+)terminal of each
•Connect one end of the BLACK cable to the NEGATIVE
•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.
TO REMOVE CABLES, REVERSE ORDER -
•BLACK cable first from chassis and then from the fully charged battery.
•RED cable last from both batteries.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
WEAK OR | FULLY CHARGED | |||||||||||||||||||||||||
DEAD BATTERY | BATTERY | |||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Fig. 35