Poulan 180002 owner manual Transmission REMOVAL/REPLACEMENT, To Adjust Steering Wheel Alignment

Page 23

SERVICE AND ADJUSTMENTS

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See “PURGE TRANSMIS- SION” in the Operation section of this manual.

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 26)

The motion control lever has been preset at the factory and adjustment should not be necessary.

•Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

•Start engine and move motion control lever until tractor does not move forward or backward.

•Hold motion control lever in that position and turn engine off.

•While holding motion control lever in place, loosen the adjustment bolt.

•Move motion control lever to the neutral (N) (lock gate) position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

•Loosen the adjustment bolt.

•Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

•Tighten adjustment bolt securely.

•Start engine and test.

•If tractor still creeps, repeat above steps until satisfied.

MOTION CONTROL

NEUTRAL

LOCK GATE

LEVER

 

 

ADJUSTMENT

 

BOLT

FIG. 26

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe- in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 27)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY

(REAR WHEEL ONLY)

FIG. 27

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents PR20H42STD II. Slope Operation Safety RulesIV. Service General OperationSafe Operation Practices for Ride-On Mowers Safety RulesTable of Contents Slope Sheet Unassembled PartsSteering Wheel Seat To Remove Tractor from CAR- TON AssemblyTools Required for Assembly HOW to SET UP Your TractorTo SET UP Your Mower for Mulching Install Seat See FigCheck for Proper Position of ALL Belts To Convert to Bagging or DISCHARG- INGCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor To USE Throttle Control see FIG HOW to USE Your TractorTo Transport See Figs To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsADD Gasoline Before Starting the EngineTowing Carts and Other ATTACH- Ments Check Engine OIL LevelPurge Transmission Mowing TipsMulching Mowing Tips Before Each USE ¿ Lubrication ChartCustomer Responsibilities General RecommendationsTractor Engine Muffler Clean AIR INTAKE/COOLING AreasCleaning Engine OIL FilterTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower HousingRecheck side-to-side adjustment To Replace Motion Drive Belt See Fig To Adjust Brake See FigBelt Installation To Replace Mower Blade Drive Belt See FigFront Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTransaxle Motion Control Lever Neutral Adjustment See Fig To Adjust Steering Wheel AlignmentTo Attach Jumper Cables To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Replace Headlight BulbTo Replace Fuse To Adjust CarburetorInterlocks and Relays Engine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number PR20H42STD SchematicElectrical KEY Part Description Chassis 174619 Drive Transaxle Hydro Gear Steering Assembly KEY Part NO. NO. Description Seat Assembly Wheels and Tires DecalsSpark Arrester EngineOptional Equipment 170771 Control Throt Mower Deck 17060612 Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Parts and Service

180002 specifications

The Poulan 180002 is a chainsaw that stands out in the realm of outdoor power equipment, particularly favored by both enthusiasts and professionals for its robust performance and innovative features. Engineered to tackle a variety of cutting tasks, this model blends power, efficiency, and user comfort into a reliable tool for both seasoned loggers and home users alike.

One of the key attributes of the Poulan 180002 is its powerful engine. Equipped with a 18-inch bar and a reliable gas engine, the chainsaw delivers an impressive level of torque, making it capable of felling trees, trimming branches, and performing other heavy-duty cutting tasks with ease. The efficient engine design ensures that it operates smoothly, allowing for long operational periods without overheating or performance dips.

The Poulan 180002 incorporates advanced technology features that enhance its usability in various environments. One notable feature is its Easy Start system, which reduces the amount of effort needed to start the chainsaw. This is especially useful for users who may experience difficulty starting traditional pull-start engines. Additionally, the chainsaw includes a tool-less chain tensioning system, allowing users to adjust the chain quickly and easily without the need for extra tools. This convenience feature ensures that the chain remains properly tensioned for optimal performance.

Safety is a paramount concern in chainsaw operation, and the Poulan 180002 addresses this with several built-in safety features. It includes a chain brake mechanism that stops the chain quickly in the event of kickback, helping to protect the user from accidents. Additionally, the chainsaw is equipped with a front hand guard to provide extra protection during operations.

In terms of design, the Poulan 180002 is ergonomically crafted for user comfort. The handle is designed to provide a secure grip, reducing vibration and fatigue during extended use. The lightweight construction further contributes to its ease of handling, making it an ideal choice for both professional and casual users.

Overall, the Poulan 180002 combines power, innovative technology, and user-friendly features, making it a versatile and dependable chainsaw. Whether you’re tackling tough trees or handling routine yard work, this chainsaw is engineered to meet a wide range of cutting needs with precision and reliability. With its compelling mix of performance and convenience, the Poulan 180002 makes an excellent addition to any outdoor toolkit.
Top Page Image Contents