Poulan 180002 owner manual Tools Required for Assembly, To Remove Tractor from CAR- TON

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

Utility knife

Pliers

(1)

9/16" wrenches

Tire pressure gauge

(2)

1/2" wrenches

 

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CAR- TON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut, from top to bottom, along lines on all four corners of carton, and lay panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft. Align mounting holes in extension and lower shafts and install 5/16 hex bolt and locknut. Tighten securely.

IMPORTANT: TIGHTEN BOLT AND NUTS SECURELY TO 18-22 FT. LBS TORQUE.

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, 3/8 lock washer, 3/8 hex bolt and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

INSERT

3/8 HEX BOLT

3/8 LOCK WASHER

LARGE FLAT

WASHER

STEERING

STEERING

WHEEL

BOOT

 

TABS

ADAPTER

EXTENSION SHAFT

 

5/16 HEX BOLT

5/16 LOCKNUT

 

LOWER

STEERING

SHAFTTAB SLOTS

FIG. 1

HOW TO SET UP YOUR TRACTOR

CHECK BATTERY (See Fig. 2)

•Lift seat pan to raised position and open battery box door.

•If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in CUSTOMER RESPONSIBILITIES section of this manual for charging instructions).

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents PR20H42STD General Operation Safety RulesIV. Service II. Slope OperationSafety Rules Safe Operation Practices for Ride-On MowersTable of Contents Unassembled Parts Steering Wheel SeatSlope Sheet HOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CAR- TONInstall Seat See Fig To SET UP Your Mower for MulchingCheck Deck Levelness To Convert to Bagging or DISCHARG- INGCheck Tire Pressure Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To USE Throttle Control see FIGTo Operate on Hills To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Transport See FigsCheck Engine OIL Level Before Starting the EngineTowing Carts and Other ATTACH- Ments ADD GasolineMowing Tips Purge TransmissionMulching Mowing Tips General Recommendations ¿ Lubrication ChartCustomer Responsibilities Before Each USETractor Engine Engine OIL Filter Clean AIR INTAKE/COOLING AreasCleaning MufflerTo Level Mower Housing Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigRecheck side-to-side adjustment To Replace Mower Blade Drive Belt See Fig To Adjust Brake See FigBelt Installation To Replace Motion Drive Belt See FigTo Adjust Steering Wheel Alignment Transmission REMOVAL/REPLACEMENTTransaxle Motion Control Lever Neutral Adjustment See Fig Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Attach Jumper CablesTo Adjust Carburetor Interlocks and RelaysTo Replace Fuse Fuel System StorageOther Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number PR20H42STDElectrical KEY Part Description Chassis 174619 Drive Transaxle Hydro Gear Steering Assembly KEY Part NO. NO. Description Seat Assembly Decals Wheels and TiresEngine Optional EquipmentSpark Arrester 170771 Control Throt Mower Deck 17060612 Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Parts and Service

180002 specifications

The Poulan 180002 is a chainsaw that stands out in the realm of outdoor power equipment, particularly favored by both enthusiasts and professionals for its robust performance and innovative features. Engineered to tackle a variety of cutting tasks, this model blends power, efficiency, and user comfort into a reliable tool for both seasoned loggers and home users alike.

One of the key attributes of the Poulan 180002 is its powerful engine. Equipped with a 18-inch bar and a reliable gas engine, the chainsaw delivers an impressive level of torque, making it capable of felling trees, trimming branches, and performing other heavy-duty cutting tasks with ease. The efficient engine design ensures that it operates smoothly, allowing for long operational periods without overheating or performance dips.

The Poulan 180002 incorporates advanced technology features that enhance its usability in various environments. One notable feature is its Easy Start system, which reduces the amount of effort needed to start the chainsaw. This is especially useful for users who may experience difficulty starting traditional pull-start engines. Additionally, the chainsaw includes a tool-less chain tensioning system, allowing users to adjust the chain quickly and easily without the need for extra tools. This convenience feature ensures that the chain remains properly tensioned for optimal performance.

Safety is a paramount concern in chainsaw operation, and the Poulan 180002 addresses this with several built-in safety features. It includes a chain brake mechanism that stops the chain quickly in the event of kickback, helping to protect the user from accidents. Additionally, the chainsaw is equipped with a front hand guard to provide extra protection during operations.

In terms of design, the Poulan 180002 is ergonomically crafted for user comfort. The handle is designed to provide a secure grip, reducing vibration and fatigue during extended use. The lightweight construction further contributes to its ease of handling, making it an ideal choice for both professional and casual users.

Overall, the Poulan 180002 combines power, innovative technology, and user-friendly features, making it a versatile and dependable chainsaw. Whether you’re tackling tough trees or handling routine yard work, this chainsaw is engineered to meet a wide range of cutting needs with precision and reliability. With its compelling mix of performance and convenience, the Poulan 180002 makes an excellent addition to any outdoor toolkit.
Top Page Image Contents