Poulan 180002 owner manual Install Seat See Fig, To SET UP Your Mower for Mulching

Page 7

ASSEMBLY

SEAT PAN

LABEL

BATTERY

BOX DOOR

TERMINAL

TERMINAL

FIG. 2

INSTALL SEAT (See Fig. 3)

Adjust seat before tightening adjustment knob.

•Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard packing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjustment knob and flat washer loosely. Do not tighten.

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment knob securely.

SEAT

SEAT PAN

SHOULDER

BOLT

FLAT WASHER

ADJUSTMENT

KNOB

FIG. 3

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

TO ROLL TRACTOR OFF SKID (See Opera- tion section, page 10, for location and func- tion of controls)

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Release parking brake by depressing clutch/brake pedal.

•Place freewheel control in freewheeling position to disengage transmission (See “TO TRANSPORT” in the Operation section of this manual).

•Roll tractor forward off skid.

•Remove banding holding deflector shield up against tractor.

TO DRIVE TRACTOR OFF SKID (See Opera- tion section, page 10, for location and func- tion of controls)

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

•Be sure all the above assembly steps have been completed.

•Check engine oil level and fill fuel tank with gasoline.

•Place freewheel control in "transmission engaged" po- sition.

•Sit on seat in operating position, depress clutch/brake pedal and set the parking brake.

•Place motion control lever in neutral (N) position.

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Start the engine. After engine has started, move throttle control to idle position.

•Release parking brake.

•Slowly move the motion control lever forward and slowly drive tractor off skid.

•Apply brake to stop tractor, set parking brake and place motion control lever in neutral position.

•Turn ignition key to "OFF" position.

Continue with the instructions that follow.

I M P O R T A N T : F O R S H I P P I N G P U R P O S E S , T H E MULCHER PLATE WAS PREATTACHED TO YOUR MOWER. THE MULCHER PLATE MUST ONLY BE USED WITH THE MULCHING BLADES THAT CAME PACKED SEPARATELY IN THE CARTON.

YOUR MOWER CAME FACTORY EQUIPPED WITH HIGH PERFORMANCE BLADES, WHICH ARE THE BEST BLADES FOR BAGGING AND DISCHARGING. TO USE YOUR MOWER WITH THE HIGH PERFORMANCE BLADES THE MULCHER PLATE MUST BE REMOVED FROM THE MOWER (SEE FIG. 4).

TO SET UP YOUR MOWER FOR MULCHING

•Remove high performance blades and install mulcher blades, (see BLADE REMOVAL in the CUSTOMER RESPONSABILITY section of this manual).

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents PR20H42STD II. Slope Operation Safety RulesIV. Service General OperationSafe Operation Practices for Ride-On Mowers Safety RulesTable of Contents Steering Wheel Seat Unassembled PartsSlope Sheet To Remove Tractor from CAR- TON AssemblyTools Required for Assembly HOW to SET UP Your TractorTo SET UP Your Mower for Mulching Install Seat See FigCheck for Proper Position of ALL Belts To Convert to Bagging or DISCHARG- INGCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor To USE Throttle Control see FIG HOW to USE Your TractorTo Transport See Figs To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsADD Gasoline Before Starting the EngineTowing Carts and Other ATTACH- Ments Check Engine OIL LevelPurge Transmission Mowing TipsMulching Mowing Tips Before Each USE ¿ Lubrication ChartCustomer Responsibilities General RecommendationsTractor Engine Muffler Clean AIR INTAKE/COOLING AreasCleaning Engine OIL FilterTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower HousingRecheck side-to-side adjustment To Replace Motion Drive Belt See Fig To Adjust Brake See FigBelt Installation To Replace Mower Blade Drive Belt See FigFront Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTransaxle Motion Control Lever Neutral Adjustment See Fig To Adjust Steering Wheel AlignmentTo Attach Jumper Cables To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Replace Headlight BulbInterlocks and Relays To Adjust CarburetorTo Replace Fuse Engine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number PR20H42STD SchematicElectrical KEY Part Description Chassis 174619 Drive Transaxle Hydro Gear Steering Assembly KEY Part NO. NO. Description Seat Assembly Wheels and Tires DecalsOptional Equipment EngineSpark Arrester 170771 Control Throt Mower Deck 17060612 Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Parts and Service

180002 specifications

The Poulan 180002 is a chainsaw that stands out in the realm of outdoor power equipment, particularly favored by both enthusiasts and professionals for its robust performance and innovative features. Engineered to tackle a variety of cutting tasks, this model blends power, efficiency, and user comfort into a reliable tool for both seasoned loggers and home users alike.

One of the key attributes of the Poulan 180002 is its powerful engine. Equipped with a 18-inch bar and a reliable gas engine, the chainsaw delivers an impressive level of torque, making it capable of felling trees, trimming branches, and performing other heavy-duty cutting tasks with ease. The efficient engine design ensures that it operates smoothly, allowing for long operational periods without overheating or performance dips.

The Poulan 180002 incorporates advanced technology features that enhance its usability in various environments. One notable feature is its Easy Start system, which reduces the amount of effort needed to start the chainsaw. This is especially useful for users who may experience difficulty starting traditional pull-start engines. Additionally, the chainsaw includes a tool-less chain tensioning system, allowing users to adjust the chain quickly and easily without the need for extra tools. This convenience feature ensures that the chain remains properly tensioned for optimal performance.

Safety is a paramount concern in chainsaw operation, and the Poulan 180002 addresses this with several built-in safety features. It includes a chain brake mechanism that stops the chain quickly in the event of kickback, helping to protect the user from accidents. Additionally, the chainsaw is equipped with a front hand guard to provide extra protection during operations.

In terms of design, the Poulan 180002 is ergonomically crafted for user comfort. The handle is designed to provide a secure grip, reducing vibration and fatigue during extended use. The lightweight construction further contributes to its ease of handling, making it an ideal choice for both professional and casual users.

Overall, the Poulan 180002 combines power, innovative technology, and user-friendly features, making it a versatile and dependable chainsaw. Whether you’re tackling tough trees or handling routine yard work, this chainsaw is engineered to meet a wide range of cutting needs with precision and reliability. With its compelling mix of performance and convenience, the Poulan 180002 makes an excellent addition to any outdoor toolkit.
Top Page Image Contents