Poulan 180241 To Adjust Gauge Wheels See Fig, To Operate Mower See Fig, To Operate on Hills

Page 12

OPERATION

•For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 7)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole with shoulder bolt, 3/8 washer, and 3/8-16 locknut and tighten securely.

•Repeat for opposite side installing gauge wheel in same adjustment hole.

3/8-16

LOCKNUT

GUAGE WHEEL

MOUNTING

BRACKET

3/8 WASHER

SHOULDER

GAUGE WHEEL

BOLT

 

FIG. 7

TO OPERATE MOWER (See Fig. 8)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.

•Select desired height of cut.

•Lower mower with attachment lift control.

•Start mower blades by engaging attachment clutch control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield in place.

"ENGAGED" POSITION

ATTACHMENT LIFT LEVER HIGH POSITION

ATTACHMENT

 

CLUTCH LEVER

LOW

"DISENGAGED"

POSITION

POSITION

 

DEFLECTOR

SHIELD

FIG. 8

TO OPERATE ON HILLS

CAUTION: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If slowing is necessary, move throttle control lever to slower position.

•If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake.

•Move motion control lever to neutral (N) position.

IMPORTANT: THE MOTION CONTROL LEVER DOES NOT RETURN TO NEUTRAL (N) POSITION WHEN THE CLUTCH/BRAKE PEDAL IS DEPRESSED.

•To restart movement, slowly release parking brake and clutch/brake pedal.

•Slowly move motion control lever to slowest setting.

•Make all turns slowly.

TO TRANSPORT (See Figs. 5 and 9)

When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor.

•Raise attachment lift to highest position with attach- ment lift control.

•Pull freewheel control out and down into the slot and release so it is held in the disengaged position.

•Do not push or tow tractor at more than two (2) MPH.

•To reengage transmission, reverse above procedure.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents PR185H42STE Safety Rules IV. ServiceGeneral Operation II. Slope OperationSafety Rules Table of Contents Unassembled Parts Steering Wheel SeatSlope Sheet Assembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig To SET UP Your Mower for Mulching Check Tire PressureCheck Deck Levelness To Convert to Bagging or DischargingOperation Know Your Tractor Motion Control Lever Selects the speedHOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To Transport See FigsBefore Starting the Engine Towing Carts and Other ATTACH- MentsCheck Engine OIL Level ADD GasolineMowing Tips Purge TransmissionMulching Mowing Tips Lubrication Chart Service DatesCustomer Responsibilities General RecommendationsTractor Brake OperationTires Operator Presence SystemEngine Clean AIR Screen Clean AIR INTAKE/COOLING AreasCleaning Engine OIL FilterService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Adjust Brake See Fig Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTransmission REMOVAL/REPLACEMENT Transaxle Motion Control Lever Neutral Adjustment See FigTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERTo Start Engine with a Weak Battery See Fig Replacing Battery See FigsTo Replace Headlight Bulb To Attach Jumper CablesTo Adjust Carburetor Interlocks and RelaysTo Replace Fuse Storage OtherFuel System Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number PR185H42STEElectrical KEY Part Description Chassis Screw Hex Wshd 8-18 x 7/8 Drive KEY Steering Assembly KEY Part NO. NO. Description Seat Assembly Decals Wheels and TiresEngine Optional EquipmentSpark Arrester 170771 Control, Throttle Mower Deck Wheel, Gauge Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

180241 specifications

The Poulan 180241 chainsaw is a reliable tool designed for both professional and home users who require efficiency and ease of use. Known for its robust performance and various features, this model stands out in the competitive world of power tools.

One of the main features of the Poulan 180241 is its powerful 18-inch bar and chain, which provide enough length to tackle medium-sized trees and larger branches with precision. The chainsaw is equipped with a potent two-cycle engine that delivers impressive power while ensuring a smooth operation. This engine is specifically designed to provide high RPMs, enabling users to make quick work of their cutting tasks.

The Poulan 180241 incorporates advanced technology aimed at enhancing user experience and safety. One such technology is the automatic oiling system, which ensures that the chain remains adequately lubricated during use. This feature not only enhances the performance of the chainsaw but also prolongs the life of the chain and bar, reducing wear and tear over time.

Another standout characteristic of the Poulan 180241 is its lightweight design, which makes it easy to maneuver for extended periods without causing fatigue. This design is complemented by a comfortable grip, allowing for better control and handling, which is especially beneficial for intricate cuts and prolonged usage.

Safety is a critical consideration in the design of the Poulan 180241. The chainsaw comes equipped with a chain brake, which allows for immediate stopping of the chain in case of kickback, a common hazard when operating chainsaws. Additionally, the model includes protective guards and ergonomic handles that provide added safety while working.

Furthermore, maintenance of the Poulan 180241 is straightforward, thanks to features like the tool-less chain tensioning system. This allows users to adjust the chain tension conveniently without the need for additional tools, ensuring optimal performance and safety.

In summary, the Poulan 180241 chainsaw combines power, efficiency, and user-friendly features, making it an ideal choice for both casual users and professionals. With robust construction, advanced technologies, and safety features, it provides a reliable solution for various cutting tasks, demonstrating Poulan's commitment to quality and innovation in power tools.
Top Page Image Contents