Poulan 180241 owner manual Off

Page 28

TROUBLESHOOTING POINTS

PROBLEM

CAUSE

CORRECTION

Engine continues to run

1.

Faulty operator-safety presence control system.

1.

Check wiring, switches and connections. If not

when operator leaves seat

 

 

 

corrected, contact an authorized service center/

with attachment clutch

 

 

 

department.

engaged

 

 

 

 

 

 

 

 

 

Poor cut - uneven

1.

Worn, bent or loose blade.

1.

Replace blade. Tighten blade bolt.

 

2.

Mower deck not level.

2.

Level mower deck.

 

3.

Buildup of grass, leaves, and trash under mower.

3.

Clean underside of mower housing.

 

4.

Bent blade mandrel.

4.

Replace blade mandrel.

 

5.

Clogged mower deck vent holes from buildup of

5.

Clean around mandrels to open vent holes.

 

 

grass, leaves, and trash around mandrels.

 

 

 

 

 

 

 

Mower blades will not

1.

Obstruction in clutch mechanism.

1.

Remove obstruction.

rotate

2.

Worn/damaged mower drive belt.

2.

Replace mower drive belt.

 

3.

Frozen idler pulley.

3.

Replace idler pulley.

 

4.

Frozen blade mandrel.

4.

Replace blade mandrel.

 

 

 

 

 

Poor grass discharge

1.

Engine speed too slow.

1.

Place throttle control in “FAST” position.

 

2.

Travel speed too fast.

2.

Shift to slower speed.

 

3.

Wet grass.

3.

Allow grass to dry before mowing.

 

4.

Mower deck not level.

4.

Level mower deck.

 

5.

Low/uneven tire air pressure.

5.

Check tires for proper air pressure.

 

6.

Worn, bent or loose blade.

6.

Replace/sharpen blade. Tighten blade bolt.

 

7.

Buildup of grass, leaves and trash under mower.

7.

Clean underside of mower housing.

 

8.

Mower drive belt worn.

8.

Replace mower drive belt.

 

9.

Blades improperly installed.

9.

Reinstall blades sharp edge down.

 

10.

Improper blades used.

10.

Replace with blades listed in this manual.

 

11.

Clogged mower deck vent holes from buildup of

11.

Clean around mandrels to open vent holes.

 

 

grass, leaves, and trash around mandrels.

 

 

 

 

 

 

 

Headlight(s) not working

1.

Switch is “OFF”.

1.

Turn switch “ON”.

(if so equipped)

2.

Bulb(s) or lamp(s) burned out.

2.

Replace bulb(s) or lamp(s).

 

3.

Faulty light switch.

3.

Check/replace light switch.

 

4.

Loose or damaged wiring.

4.

Check wiring and connections.

 

5.

Blown fuse.

5.

Replace fuse.

 

 

 

 

 

Battery will not charge

1.

Bad battery cell(s).

1.

Replace battery.

 

2.

Poor cable connections.

2.

Check/clean all connections.

 

3.

Faulty regulator (if so equipped).

3.

Replace regulator.

 

4.

Faulty alternator.

4.

Replace alternator.

 

 

 

 

 

Loss of drive

1.

Freewheel control in “disengaged” position.

1.

Place freewheel control in “engaged” position.

 

2.

Motion drive belt worn, damaged, or broken.

2.

Replace motion drive belt.

 

3.

Air trapped in transmission during shipment

3.

Purge transmission.

 

 

or servicing.

 

 

 

 

 

 

 

Engine “backfires”

1.

Engine throttle control not set at “SLOW”

1.

Move throttle control to “SLOW” position and allow

when turning engine

 

position for 30 seconds before stopping engine.

 

to idle for 30 seconds before stopping engine.

“OFF”

 

 

 

 

 

 

 

 

 

28

Page 27 Page 29
Image 28
Page 27 Page 29
Contents PR185H42STE Safety Rules IV. ServiceGeneral Operation II. Slope OperationSafety Rules Table of Contents Steering Wheel Seat Unassembled PartsSlope Sheet Assembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig To SET UP Your Mower for Mulching Check Tire PressureCheck Deck Levelness To Convert to Bagging or DischargingOperation Know Your Tractor Motion Control Lever Selects the speedHOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To Transport See FigsBefore Starting the Engine Towing Carts and Other ATTACH- MentsCheck Engine OIL Level ADD GasolineMowing Tips Purge TransmissionMulching Mowing Tips Lubrication Chart Service DatesCustomer Responsibilities General RecommendationsTractor Brake OperationTires Operator Presence SystemEngine Clean AIR Screen Clean AIR INTAKE/COOLING AreasCleaning Engine OIL FilterTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Adjust Brake See Fig Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTransmission REMOVAL/REPLACEMENT Transaxle Motion Control Lever Neutral Adjustment See FigTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERTo Start Engine with a Weak Battery See Fig Replacing Battery See FigsTo Replace Headlight Bulb To Attach Jumper CablesInterlocks and Relays To Adjust CarburetorTo Replace Fuse Storage OtherFuel System Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number PR185H42STEElectrical KEY Part Description Chassis Screw Hex Wshd 8-18 x 7/8 Drive KEY Steering Assembly KEY Part NO. NO. Description Seat Assembly Decals Wheels and TiresOptional Equipment EngineSpark Arrester 170771 Control, Throttle Mower Deck Wheel, Gauge Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

180241 specifications

The Poulan 180241 chainsaw is a reliable tool designed for both professional and home users who require efficiency and ease of use. Known for its robust performance and various features, this model stands out in the competitive world of power tools.

One of the main features of the Poulan 180241 is its powerful 18-inch bar and chain, which provide enough length to tackle medium-sized trees and larger branches with precision. The chainsaw is equipped with a potent two-cycle engine that delivers impressive power while ensuring a smooth operation. This engine is specifically designed to provide high RPMs, enabling users to make quick work of their cutting tasks.

The Poulan 180241 incorporates advanced technology aimed at enhancing user experience and safety. One such technology is the automatic oiling system, which ensures that the chain remains adequately lubricated during use. This feature not only enhances the performance of the chainsaw but also prolongs the life of the chain and bar, reducing wear and tear over time.

Another standout characteristic of the Poulan 180241 is its lightweight design, which makes it easy to maneuver for extended periods without causing fatigue. This design is complemented by a comfortable grip, allowing for better control and handling, which is especially beneficial for intricate cuts and prolonged usage.

Safety is a critical consideration in the design of the Poulan 180241. The chainsaw comes equipped with a chain brake, which allows for immediate stopping of the chain in case of kickback, a common hazard when operating chainsaws. Additionally, the model includes protective guards and ergonomic handles that provide added safety while working.

Furthermore, maintenance of the Poulan 180241 is straightforward, thanks to features like the tool-less chain tensioning system. This allows users to adjust the chain tension conveniently without the need for additional tools, ensuring optimal performance and safety.

In summary, the Poulan 180241 chainsaw combines power, efficiency, and user-friendly features, making it an ideal choice for both casual users and professionals. With robust construction, advanced technologies, and safety features, it provides a reliable solution for various cutting tasks, demonstrating Poulan's commitment to quality and innovation in power tools.
Top Page Image Contents