Poulan 180241 owner manual Tools Required for Assembly, To Remove Tractor from Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

Utility knife

Pliers

(1)

9/16" wrenches

Tire pressure gauge

(2)

1/2" wrenches

 

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut, from top to bottom, along lines on all four corners of carton, and lay panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

INSERT

3/8 HEX BOLT

3/8 LOCK WASHER

LARGE FLAT

WASHER

STEERING

WHEELSTEERING BOOT

TABS

ADAPTER

EXTENSION SHAFT

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft. Align mount- ing holes in extension and lower shafts and install 5/16 hex bolt and locknut. Tighten securely.

IMPORTANT: TIGHTEN BOLT AND NUT SECURELY TO 18-22 FT. LBS TORQUE.

•

Place tabs of steering boot over tab slots in dash and push

5/16 LOCKNUT

LOWER

STEERING

5/16 HEX BOLT

down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, 3/8 lock washer, 3/8 hex bolt and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

SHAFTTAB SLOTS

FIG. 1

HOW TO SET UP YOUR TRACTOR

CHECK BATTERY (See Fig. 2)

•Lift seat pan to raised position.

•If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in CUSTOMER RESPONSIBILITIES section of this manual for charging instructions).

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents PR185H42STE General Operation Safety RulesIV. Service II. Slope OperationSafety Rules Table of Contents Unassembled Parts Steering Wheel SeatSlope Sheet HOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig Check Deck Levelness To SET UP Your Mower for MulchingCheck Tire Pressure To Convert to Bagging or DischargingOperation Know Your Tractor Motion Control Lever Selects the speedHOW to USE Your Tractor To Operate on Hills To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Transport See FigsCheck Engine OIL Level Before Starting the EngineTowing Carts and Other ATTACH- Ments ADD GasolineMowing Tips Purge TransmissionMulching Mowing Tips Customer Responsibilities Lubrication ChartService Dates General RecommendationsTires TractorBrake Operation Operator Presence SystemEngine Cleaning Clean AIR ScreenClean AIR INTAKE/COOLING Areas Engine OIL FilterService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Replace Mower Blade Drive Belt See Fig To Adjust Brake See FigBelt Installation To Replace Motion Drive Belt See FigTo Adjust Steering Wheel Alignment Transmission REMOVAL/REPLACEMENTTransaxle Motion Control Lever Neutral Adjustment See Fig Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Attach Jumper CablesTo Adjust Carburetor Interlocks and RelaysTo Replace Fuse Fuel System StorageOther Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number PR185H42STEElectrical KEY Part Description Chassis Screw Hex Wshd 8-18 x 7/8 Drive KEY Steering Assembly KEY Part NO. NO. Description Seat Assembly Decals Wheels and TiresEngine Optional EquipmentSpark Arrester 170771 Control, Throttle Mower Deck Wheel, Gauge Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

180241 specifications

The Poulan 180241 chainsaw is a reliable tool designed for both professional and home users who require efficiency and ease of use. Known for its robust performance and various features, this model stands out in the competitive world of power tools.

One of the main features of the Poulan 180241 is its powerful 18-inch bar and chain, which provide enough length to tackle medium-sized trees and larger branches with precision. The chainsaw is equipped with a potent two-cycle engine that delivers impressive power while ensuring a smooth operation. This engine is specifically designed to provide high RPMs, enabling users to make quick work of their cutting tasks.

The Poulan 180241 incorporates advanced technology aimed at enhancing user experience and safety. One such technology is the automatic oiling system, which ensures that the chain remains adequately lubricated during use. This feature not only enhances the performance of the chainsaw but also prolongs the life of the chain and bar, reducing wear and tear over time.

Another standout characteristic of the Poulan 180241 is its lightweight design, which makes it easy to maneuver for extended periods without causing fatigue. This design is complemented by a comfortable grip, allowing for better control and handling, which is especially beneficial for intricate cuts and prolonged usage.

Safety is a critical consideration in the design of the Poulan 180241. The chainsaw comes equipped with a chain brake, which allows for immediate stopping of the chain in case of kickback, a common hazard when operating chainsaws. Additionally, the model includes protective guards and ergonomic handles that provide added safety while working.

Furthermore, maintenance of the Poulan 180241 is straightforward, thanks to features like the tool-less chain tensioning system. This allows users to adjust the chain tension conveniently without the need for additional tools, ensuring optimal performance and safety.

In summary, the Poulan 180241 chainsaw combines power, efficiency, and user-friendly features, making it an ideal choice for both casual users and professionals. With robust construction, advanced technologies, and safety features, it provides a reliable solution for various cutting tasks, demonstrating Poulan's commitment to quality and innovation in power tools.
Top Page Image Contents