Poulan XT19H42YT Before Starting the Engine, Reverse Operation System ROS, To Operate on Hills

Page 11

OPERATION

REVERSE OPERATION SYSTEM (ROS)

Your tractor is equipped with a Reverse Operation System (ROS). Any attempt by the operator to travel in the reverse direction with the attachment clutch engaged will shut off the engine unless ignition key is placed in the ROS "ON" position.

WARNING: Backing up with the attachment clutch en- gaged while mowing is strongly discouraged. Turning the ROS "ON", to allow reverse operation with the attachment clutch engaged, should only be done when the operator decides it is necessary to reposition the machine with the attachment engaged. Do not mow in reverse unless absolutely necessary.

USING THE REVERSE OPERATION SYSTEM -

Only use if you are certain no children or other bystanders will enter the mowing area.

•Move motion control lever to neutral (N) position.

•With engine running, turn ignition key counterclockwise to ROS "ON" position.

•Look down and behind before and while backing.

•Slowly move motion control lever to reverse (R) position to start movement.

•When use of the ROS is no longer needed, turn the ignition key clockwise to engine "ON" position.

ROS "ON" POSITION

ENGINE "ON" POSITION

 

(NORMAL OPERATING)

02828

TO OPERATE ON HILLS

CAUTION: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake.

•Move motion control lever to neutral (N) position.

IMPORTANT: THE MOTION CONTROL LEVER DOES NOT RETURN TO NEUTRAL (N) POSITION WHEN THE CLUTCH/ BRAKE PEDAL IS DEPRESSED.

•To restart movement, slowly release parking brake and clutch/brake pedal.

•Slowly move motion control lever to slowest setting.

•Make all turns slowly.

TO TRANSPORT (See Figs. 3 and 11)

When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor.

•Raise attachment lift to highest position with attachment lift control.

•Pull freewheel control out and down into the slot and release so it is held in the disengaged position.

•Do not push or tow tractor at more than two (2) MPH.

•To reengage transmission, reverse above procedure.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

Transmission Engaged

Transmission Disengaged

FIG. 11

TOWING CARTS AND OTHER ATTACHMENTS

Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your trac- tor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

The engine in your tractor has been shipped, from the factory, already filled with summer weight oil.

•Check engine oil with tractor on level ground.

•Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•For cold weather operation you should change oil for easier starting (See “OIL VISCOSITY CHART” in the Maintenance section of this manual).

•To change engine oil, see the Maintenance section in this manual.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Always Wear EYE Protection During Operation XT19H42YTII. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceIII. Children Table of Contents Unpack Carton AssemblyUnassembled Parts To Remove Tractor from CartonCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor To USE Throttle Control D See Fig HOW to USE Your TractorTo SET Parking BRAKESee Fig StoppingTo Operate Mower To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Move Forward and Backward See FigTo Transport See Figs Before Starting the EngineReverse Operation System ROS To Operate on HillsAutomatic Transmission Warm UP ADD GasolineTo Start Engine See Fig Purge TransmissionMowing Tips Before Each USE MaintenanceTires BatteryTractor Brake OperationEngine Spark Plugs CleaningEngine OIL Filter MufflerTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Figs To Level Mower To Replace Motion Drive Belt See Fig To Replace Mower Drive Belt See FigTo Check Brake To Attach Jumper Cables To Start Engine with a Weak Battery See FigFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Points Engine dies when Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationPage Parts and Service

XT19H42YT specifications

The Poulan XT19H42YT is a robust and versatile lawn tractor designed to meet the needs of both homeowners and landscaping professionals. With its powerful engine and comprehensive features, this model offers exceptional performance and durability for various mowing tasks.

At the heart of the XT19H42YT is a reliable 19 horsepower engine. This engine provides the necessary power to handle larger lawns and more challenging terrains with ease. It is designed for optimal fuel efficiency, allowing for extended run times without the need for frequent refueling. Coupled with an automatic transmission, users can experience a smooth and effortless driving experience, making it easy to navigate through tight spaces and around obstacles.

One of the standout features of the XT19H42YT is its 42-inch cutting deck. This mid-sized deck is ideal for mowing in various conditions, allowing users to cut a wide swath with each pass. The cutting height is easily adjustable, providing the flexibility to achieve the desired length for different grass types or seasonal changes. The deck is also designed for enhanced airflow, which promotes a clean and even cut while preventing clumping.

Another impressive characteristic of the Poulan XT19H42YT is its Hydrostatic transmission. This technology allows for seamless speed adjustments without the need for shifting gears, enabling the operator to maintain full control over the tractor's speed depending on the mowing conditions. This feature is especially useful when transitioning between different terrain types or navigating around trees and flower beds.

The XT19H42YT also includes ergonomic features such as an adjustable high-back seat, offering comfort during extended mowing sessions. The easy-access controls ensure that everything from starting the engine to adjusting the cutting height is within easy reach, enhancing the overall user experience.

The tractor is equipped with sturdy construction and reliable components that contribute to its longevity and performance. With a steel chassis and reinforced cutting deck, the Poulan XT19H42YT is built to withstand the rigors of regular use, making it a solid investment for any lawn care enthusiast.

In summary, the Poulan XT19H42YT stands out with its powerful 19 horsepower engine, efficient hydrostatic transmission, and versatile 42-inch cutting deck. Its robust build quality and user-friendly features make it an excellent choice for anyone looking to maintain their lawn with efficiency and ease.
Top Page Image Contents