Poulan XT19H42YT manual ADD Gasoline, To Start Engine See Fig, Purge Transmission

Page 12

OPERATION

ADD GASOLINE

•Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

IMPORTANT: WHEN OPERATING IN TEMPERATURES BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE GASOLINE TO HELP INSURE GOOD COLD WEATHER STARTING.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

TO START ENGINE (See Fig. 3)

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

•Be sure freewheel control is in the transmission engaged position.

•Sit on seat in operating position, depress clutch/brake pedal and set parking brake.

•Place motion control lever in neutral (N) position.

•Move attachment clutch to “DISENGAGED” position.

•Move throttle control to choke position.

NOTE: Before starting, read the warm and cold starting procedures below.

•Insert key into ignition and turn key clockwise to“START” position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, move throttle control to fast position, wait a few minutes and try again. If engine still does not start, move the throttle control back to the choke position and retry.

WARM WEATHER STARTING (50° F and above)

•When engine starts, move the throttle control to the fast position.

•The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING ( 50° F and below)

•When engine starts, allow engine to run with the throttle control in the choke position until the engine runs roughly, then move throttle control to fast position. This may re- quire an engine warm-up period from several seconds to several minutes, depending on the temperature.

AUTOMATIC TRANSMISSION WARM UP

•Before driving the unit in cold weather, the transmission should be warmed up as follows:

•Be sure the tractor is on level ground.

•Place the motion control lever in neutral. Release the parking brake and let the clutch/brake slowly return to operating position.

•Allow one minute for transmission to warm up.This can be done during the engine warm up period.

•The attachments can also be used during the engine warm-up period after the transmission has been warmed up.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual.

PURGE TRANSMISSION

CAUTION: Never engage or disengage freewheel lever while the engine is run-

ning.

To ensure proper operation and performance, it is recom- mended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have de- veloped during shipping of your tractor.

IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD BE PURGED AFTER REINSTALLATION BEFORE OPERATING THE TRACTOR.

•Place tractor safely on a level surface - that is clear and open - with engine off and parking brake set.

•Disengage transmission by placing freewheel control in freewheeling position (See “TO TRANSPORT” in this section of manual).

•Sitting in the tractor seat, start engine. After the engine is running, move throttle control to slow position. With motion control lever in neutral (N) position, slowly dis- engage clutch/brake pedal.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents XT19H42YT Always Wear EYE Protection During OperationSafety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService III. ChildrenIV. Towing Table of Contents Assembly Unassembled PartsTo Remove Tractor from Carton Unpack CartonCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To SET Parking BRAKESee FigStopping To USE Throttle Control D See FigTo Adjust Mower Cutting Height See Fig To Adjust Gauge Wheels See FigTo Move Forward and Backward See Fig To Operate MowerBefore Starting the Engine Reverse Operation System ROSTo Operate on Hills To Transport See FigsADD Gasoline To Start Engine See FigPurge Transmission Automatic Transmission Warm UPMowing Tips Maintenance Before Each USEBattery TractorBrake Operation TiresEngine Cleaning Engine OIL FilterMuffler Spark PlugsService and Adjustments To Remove Mower See FigTo Install Mower See Figs To Level Mower To Replace Mower Drive Belt See Fig To Check BrakeTo Replace Motion Drive Belt See Fig To Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Remove Wheel for Repairs See Fig To Attach Jumper CablesTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Engine dies when Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXPage Parts and Service

XT19H42YT specifications

The Poulan XT19H42YT is a robust and versatile lawn tractor designed to meet the needs of both homeowners and landscaping professionals. With its powerful engine and comprehensive features, this model offers exceptional performance and durability for various mowing tasks.

At the heart of the XT19H42YT is a reliable 19 horsepower engine. This engine provides the necessary power to handle larger lawns and more challenging terrains with ease. It is designed for optimal fuel efficiency, allowing for extended run times without the need for frequent refueling. Coupled with an automatic transmission, users can experience a smooth and effortless driving experience, making it easy to navigate through tight spaces and around obstacles.

One of the standout features of the XT19H42YT is its 42-inch cutting deck. This mid-sized deck is ideal for mowing in various conditions, allowing users to cut a wide swath with each pass. The cutting height is easily adjustable, providing the flexibility to achieve the desired length for different grass types or seasonal changes. The deck is also designed for enhanced airflow, which promotes a clean and even cut while preventing clumping.

Another impressive characteristic of the Poulan XT19H42YT is its Hydrostatic transmission. This technology allows for seamless speed adjustments without the need for shifting gears, enabling the operator to maintain full control over the tractor's speed depending on the mowing conditions. This feature is especially useful when transitioning between different terrain types or navigating around trees and flower beds.

The XT19H42YT also includes ergonomic features such as an adjustable high-back seat, offering comfort during extended mowing sessions. The easy-access controls ensure that everything from starting the engine to adjusting the cutting height is within easy reach, enhancing the overall user experience.

The tractor is equipped with sturdy construction and reliable components that contribute to its longevity and performance. With a steel chassis and reinforced cutting deck, the Poulan XT19H42YT is built to withstand the rigors of regular use, making it a solid investment for any lawn care enthusiast.

In summary, the Poulan XT19H42YT stands out with its powerful 19 horsepower engine, efficient hydrostatic transmission, and versatile 42-inch cutting deck. Its robust build quality and user-friendly features make it an excellent choice for anyone looking to maintain their lawn with efficiency and ease.
Top Page Image Contents