Poulan XT20H46YT manual To Adjust Mower Cutting Height See Fig, To Adjust Gauge Wheels See Fig

Page 10

OPERATION

J

K

L

FIG. 7

SYSTEM CHARACTERISTICS

The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other conditions such as trimming at slow speeds may cause the cruise control to disengage. Do not use the cruise control on slopes, rough terrian or while trimmimg or turning.

•With forward drive pedal depressed to desired speed, pull cruise control lever (J) up and hold while lifting your foot off the pedal, then release the lever.

To disengage the cruise control, depress the brake pedal or tap on forward drive pedal.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8)

The position of the attachment lift lever (A) determines the cutting height.

T

A

FIG. 8

•Put attachment lift lever in desired cutting height slot.

•Slide pointer tab (T) to desired cutting height as a reminder for next time you mow.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in this section of manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.

•Repeat for all, installing gauge wheel in same adjust- ment hole.

FIG.9

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills.

•Select desired height of cut with attachment lift lever.

•Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield (S) in place.

S

FIG. 10

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents XT20H46YT ModelGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceIV. Towing Table of Contents To Remove Tractor from Carton AssemblyUnassembled Parts Unpack CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor StoppingSystem Characteristics To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerTo Operate on Hills Before Starting the EngineReverse Operation System ROS To Transport See FigsPurge Transmission ADD GasolineTo Start Engine See Fig Automatic Transmission Warm UPMowing Tips General Recommendations MaintenanceMaintenance ScheduleBrake Operation BatteryTractor TiresEngine Muffler CleaningEngine OIL Filter Spark PlugsTo Install Mower See -21 Service and AdjustmentsTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower To Check Brake To Replace Mower Drive Belt See FigTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigReplacing Battery See Fig To Remove Wheel for Repairs See FigTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Only Ride UP and Down Hill Not Across Hill Degrees MAX Fold Along This Dotted Line Degree SlopeLimited Warranty Service Notes Service Notes Service Notes Parts and Service Changere DE Pièces LES ET L’ENTRETIEN Dentretien Remarques Dentretien Remarques Dentretien Remarques Limitée Garantie Degrés Suivant LES UNE Pliez EST CeciDépannage DE Guide Connexions les et interrupteurs les câblage, le VérifiezLame de mandrin le Remplacez Tordu est lame de mandrin Un Entreposage Reglages ET Revision Starter DU Commande LA Régler PourGAZ DES Commande LA DE Câble LE Régler Pour MoteurFig la Voir Tionsraparé LES Pour Roues LES Enlever Pour Fig la Voir Batterie LA ReplacerAvant Roue LA DE PINCEMENT/CARROSSAGE Freins LES Vérifier Pour Réglages ET RévisionFig la Voir D’ENTRAÎNEMENT Courroie a L Acer Rempl Pour 27 .FIG24 .FIG Tondeuse LA Niveau LE Ajuster Pour25 .FIG 23 .FIG20 .FIG 21 .FIG 19 .FIG18 .FIG Tondeuse LA Enlever Pour Courroie LA ET Tondeuse LA InstallerFig Voir 17 .FIG’ALLUMAGE Bougie EntretienFig la Voir Moteur DE D’HUILE FiltreSionmistrans LA DE Moteur Fluide AIR À Filtre’AIR Tamis LE Nettoyer Transmission LA DE RefroidissementFig la Voir Lame LA Enlever EN Fonctionnement DE Système ETLubrification DE Tableau Utilisation Chaque AvantUtilisation 12 .FIGQuetimaauto Transmission LA PurgerMoteur LE Démarrer Pour Sion Transmis DE Réchauffement11 et 3 .Fig les Voir MAR EN Fonctionnement DE Système10 .FIG Tondeuse LA Utiliser PourJauge DE Roues LES Régler Pour Système DU CaractéristiquesDE Régulateur LE Utiliser Comment GAZ DES Commande LA Utiliser PourVitess Fig la Voir Mentnetionsta DE Frein LE Engager PourUtilisation ’EMBRAYAGE Desmancom des tionfonc la et MontageLA DE Tracteur LE Retirer Pour Fig la Voir Batterie LA Vérifier Montées NON PiécesToncar DU Tracteur LE Sortir Pour Fig la Voir Siège LE AjustezSommaire En l’utilisation pour Conseils Général EntretienTracteurs des sécurité toute ’ESSENCE DE Sûre ManipulationLES Dans Fonctionnement PentesTracteurs des sécurité toute en l’utilisation pour Conseils AUX Imprimé

XT20H46YT specifications

The Poulan XT20H46YT is a robust and versatile riding lawn mower designed for homeowners seeking efficiency and performance in their lawn care routine. Built with power and durability in mind, this model showcases a variety of features that cater to different mowing needs and preferences.

At the heart of the XT20H46YT is its powerful 20 HP Briggs & Stratton engine, which delivers reliable performance across various terrains. The engine's design includes an easy starting system, ensuring that users can get to mowing without the frustration of traditional pull-starts. This engine pairs seamlessly with a hydrostatic transmission, allowing for smooth acceleration and effortless control of speed. This eliminates the need for shifting gears, making it user-friendly for both novice and experienced operators.

One of the standout features of the XT20H46YT is its 46-inch cutting deck. This mid-sized deck strikes an ideal balance between maneuverability and cutting efficiency, allowing users to cover larger areas while maintaining a compact size suitable for residential lawns. The mowing deck also includes a cutting height adjustment feature, which offers six preset positions, enabling homeowners to customize their lawn's appearance based on personal preference and grass type.

The Poulan XT20H46YT takes advantage of advanced technologies to enhance the user experience. Its reinforced frame construction adds durability, ensuring that the mower can withstand the rigors of regular use. Furthermore, the mower boasts larger rear tires that improve traction and stability, especially when navigating uneven surfaces or inclines.

Comfort is another priority for Poulan, and the XT20H46YT is equipped with a comfortable, high-back seat that provides support during extended mowing sessions. The ergonomically designed steering wheel is positioned for easy access, and the simple control layout allows for intuitive operation, minimizing distractions while focusing on the task at hand.

Maintenance is made easier with features such as an accessible deck wash port, which simplifies the cleaning process after mowing. Regular maintenance is crucial for optimal performance, and this added convenience encourages users to keep their equipment in top shape.

In summary, the Poulan XT20H46YT is an impressive riding lawn mower that combines power, comfort, and advanced features. With its dependable engine, user-friendly hydrostatic transmission, and versatile cutting deck, this model is a sound investment for anyone looking to maintain a pristine lawn with ease and efficiency.
Top Page Image Contents