Poulan PXT16542 manual Engine, Cleaning

Page 15

MAINTENANCE

V-BELTS

Check V-belts for deterioration and wear after 100 hours and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear.

TRANSAXLE COOLING

Keep transaxle free from build-up of dirt and chaff which can restrict cooling.

ENGINE

LUBRICATION

Only use high quality detergent oil rated with API service classification SG-SL. Select the oil’s SAE viscosity grade according to your expected operating temperature.

SAE VISCOSITY GRADES

 

 

 

 

 

 

 

 

 

 

SAE 30

 

 

 

 

 

 

5W-30

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F

-20

0

 

 

30 32 40

 

60

80

100

C

-30

-20

-10

0

10

20

30

40

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

oil_visc_chart1_e

FIG. 11

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, they will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Change the oil after every 25 hours of operation or at least once a year if the tractor is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each eight (8) hours of operation. Tighten oil fill cap/dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL (See Figs. 11 and 12)

Determine temperature range expected before oil change. All oil must meet API service classification SG-SL.

Be sure tractor is on level surface.

Oil will drain more freely when warm.

Catch oil in a suitable container.

Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine when changing oil.

Remove yellow cap from end of drain valve and install the drain tube onto the fitting.

OIL DRAIN VALVE

After oil has drained completely, close and lock the drain valve by pushing inward and turning clockwise until the pin is in the locked position as shown.

Remove the drain tube and replace the cap onto to the bottom fitting of the drain valve.

Refill engine with oil through oil fill dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual.

Use gauge on oil fill cap/dipstick for checking level. For accurate reading, insert dipstick into the tube and push down firmly into place before removing. Keep oil up to, but not over, the “FULL” line on dipstick. Push dipstick down firmly into the tube when finished.

CLEAN AIR SCREEN

Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers.

AIR FILTER

Your engine will not run properly using a dirty air filter. Service air cleaner more often under dusty conditions. See Engine Manual.

MUFFLER

Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or damage.

SPARK PLUGS

Replace spark plugs at the beginning of each mowing sea- son or after every 100 hours of use, whichever comes first. Spark plug type and gap setting is shown in "PRODUCT SPECIFICATIONS" section of this manual.

IN-LINE FUEL FILTER (See Fig. 13)

The fuel filter should be replaced once each season. If fuel filter becomes clogged, obstructing fuel flow to carburetor, replacement is required.

With engine cool, remove filter and plug fuel line sections.

Place new fuel filter in position in fuel line with arrow pointing towards carburetor.

Be sure there are no fuel line leaks and clamps are properly positioned.

Immediately wipe up any spilled gasoline.

CLAMP

CLAMP

FUEL FILTER

CLOSED

AND

CLEANING

FIG. 13

LOCKED

 

POSITION

 

YELLOW CAP

DRAIN

TUBE

 

FIG. 12

• Unlock drain valve by pushing inward and turning counterclockwise.

• To open, pull out on the drain valve.

15

Cleanengine,battery,seat,finish,etc.ofallforeignmatter.

Keep finished surfaces and wheels free of all gasoline, oil, etc.

Protect painted surfaces with automotive type wax.

We do not recommend using a garden hose or pressure washer to clean your tractor unless the engine and trans- mission are covered to keep water out. Water in engine or transmission will shorten the useful life of your tractor. Use compressed air or a leaf blower to remove grass, leaves and trash from tractor and mower.

Image 15
Contents PXT16542 II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents Unassembled Parts Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonCheck for Proper Position of ALL Belts Install Seat See FigCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Transport Before Starting the EngineTo Operate on Hills Towing Carts and Other AttachmentsMowing Tips ADD GasolineTo Start Engine See Fig Maintenance Lubrication ChartPowdered Graphite Type Lubricant Sparingly Blade Removal See Fig BatteryTractor Blade CareEngine CleaningTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower HousingBelt Removal Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Check BrakeFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel AlignmentInterlocks and Relays To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbEngine OIL StorageOther Fuel SystemProblem Cause Correction TroubleshootingExcessive To run when operBattery will not When turningFold Alon THI Dotted Line REE Lope Only Ride UP and Down Hill Not Across Hill Degrees MAXStevens Creek Road Terry Fox Way Augusta, GA 30907 USA Outdoor Products Customer Service DeptHOP Canada contactDept Service Customer Products Outdoor Canada Au AutoriséGarantie cette de exclus sont normal l’entretien et Degrés MAX Correction Cause Problème Dépannage DE GuidePuissance de Entreposage Réglages ET Révision Carburateur LE Régler PourFig la Voir Calandre LA ET Capot LE Enlever Pour Direction DE Volant LA DE L’ALIGNEMENT Régler Pour Fig la VoirVitesses DE Boîte LA DE Mentgechan DE Levier DU Neutre AU RéglageFreins LES Vérifier Pour Tondeuse DE Lame DE D’ENTRAÎNEMENTCourroie Acer Rempl Pour 16 et 15 .Fig les Voir Lautre À Côté DUN Réglage DE Boîtier LE Niveau DE Mettre PourSedeuton 14 .FIGMoteur EntretienPneus Fig la Voir Lame LA EnleverTrapézoïdales Courroies Lames DES EntretienUtilisation Chaque Avant Lubrification DE TableauMoteur de d’huile niveau le Vérifiez Dhiver Spéciale ET Propre FRAÎCHE, L’ESSENCE DE UtilisationTonte DE Conseils ’ESSENCE Réservoir LE RemplirArrière Marche EN Fonctionnement Accessoires AutresMoteur DU D’HUILE Niveau LE Vérifier Tracteur LE Transporter PourT O S I L I T U GAZ DES Commande LA Utiliser Pour02829 Moteur Sont Courroies LES Toutes SI Vérifier MontageFrein DE Système LE Vérifier Place EN CorrectementCarton LE Deballer DE Tracteur LE Retirer AvantFig la Voir Batterie LA Vérifier Tionrecdi DE Volant LE FixerSiège Montar SIN PiezasSommaire Général Entretien EnfantsEntretien RemorquageGénéral Fonctionnement AvertissementPentes LES Dans Fonctionnement Tracteurs des sécurité toute en l’utilisation pour ConseilsPelouse DE Tracteur PXT16542

PXT16542 specifications

The Poulan PXT16542 is a robust and efficient lawn mower designed for homeowners seeking a reliable and powerful cutting tool for their gardens. Boasting a 42-inch cutting deck, this riding mower is perfectly suited for medium to large lawns, enabling efficient coverage and reduced mowing time.

One of the standout features of the PXT16542 is its powerful 16.5 HP Briggs & Stratton engine. This engine delivers optimized performance with substantial torque, ensuring seamless maneuverability and cutting power on various terrains. The integrated automatic transmission further enhances the mowing experience by allowing smooth speed adjustments, making it easy to navigate around obstacles and uneven surfaces.

A crucial technology in the PXT16542 is its cutting system, featuring a dual-blade design that provides a clean and precise cut every time. With multiple height adjustment settings, users can customize the cutting height to suit their lawn's needs, whether they prefer a close trim or a higher grass finish. This flexibility is essential for maintaining a healthy lawn and promoting robust growth.

The Poulan PXT16542 is also designed for user comfort and convenience. Its ergonomic seat ensures a comfortable riding experience, even during extended mowing sessions. Easy-to-reach controls make operation intuitive, while the easy-access fuel tank simplifies refueling. The inclusion of a tight turning radius allows for exceptional maneuverability, making it easy to navigate tight spots or flowerbeds without damaging the landscape.

Durability and maintenance are prioritized in this mower’s design. The rugged construction and high-quality materials used in the PXT16542 contribute to its longevity and reliability. Additionally, the mower comes with maintenance points conveniently located for easy access, allowing for quick checks and upkeep, which ultimately prolongs the life of the machine.

In summary, the Poulan PXT16542 is an ideal choice for homeowners needing a reliable, user-friendly riding mower. With its powerful engine, versatile cutting capabilities, user-centric design, and durable construction, this mower stands out as a dependable partner for lawn care, ensuring that your garden remains in pristine condition throughout the mowing season.